Toro Z Master 500 Series Скачать руководство пользователя страница 101

Страница: 101 / 168

5-30

Z Master 500 Gas Series Service Manual

Fig 268

DSC-2823

20. Remove two bolts and nuts retaining the top and

bottom ribs and the bottom strap guard located on

the right side (Fig. 268). Remove the corresponding

bolts and nuts on the left hand side.

ENGINE

17. Unplug the two relays from the relay connectors.

Remove the two bolts and nuts retaining the

connectors to the right hand side plate (Fig. 265).

Fig 265

DSC-2818

Fig 267

DSC-2819

19. Remove the two bolts and nuts on the right side of

the machine used to hold the top rib to the right side

radiator brace (Fig. 267). Remove the corresponding

bolts and nuts on the left hand side.

Fig 266

DSC-2825

18. Remove the clamp and hose, located under the

coolant overflow tank (Fig. 266).

Содержание Z Master 500 Series









































































































































































Результаты поиска

Содержание Z Master 500 Series

Отзывы:

Toro Z Master 500 Series, Руководство по обслуживанию, Страница: 101 / 168

Результаты поиска

Содержание Z Master 500 Series

Отзывы: