background image

Fuel is harmful or fatal if swallowed. Long-term
exposure to vapors can cause serious injury and
illness.

Avoid prolonged breathing of vapors.

Keep your face away from the nozzle and
gas tank or conditioner opening.

Keep fuel away from your eyes and skin.

Under certain conditions, diesel fuel and fuel
vapors are highly flammable and explosive. A
fire or explosion from fuel can burn you and
others and can cause property damage.

Before removing the fuel tank cap, make
sure the vehicle is positioned on a level
surface. Open fuel tank cap slowly.

Use a funnel and fill the fuel tank outdoors,
in an open area, when the engine is off and
is cold. Wipe up any fuel that spills.

Do not fill the fuel tank completely full. Add
fuel to the fuel tank until the level is 1 in.
(25 mm) below the bottom of the filler neck.
This empty space in the tank allows the fuel
to expand.

Never smoke when handling fuel, and stay
away from an open flame or where fuel
fumes may be ignited by a spark.

Store fuel in a clean, safety-approved
container and keep the cap in place.

Biodiesel Ready

This machine can also use a biodiesel blended fuel
of up to B20 (20% biodiesel, 80% petrodiesel). The
petrodiesel portion should be low or ultra low sulfur.
Observe the following precautions:

The biodiesel portion of the fuel must meet
specification ASTM D6751 or EN14214.

The blended fuel composition should meet ASTM
D975 or EN590.

Painted surfaces may be damaged by biodiesel
blends.

Use B5 (biodiesel content of 5%) or lesser blends
in cold weather.

Monitor seals, hoses, gaskets in contact with fuel as
they may be degraded over time.

Fuel filter plugging may be expected for a time after
converting to biodiesel blends.

Contact your distributor if you wish for more
information on biodiesel.

1. Clean the area around the fuel tank cap.

2. Remove the fuel tank cap (Figure 18).

Figure 18

1.

Fuel tank cap

3. Fill the tank to about one inch below the top of the

tank, (bottom of the filler neck), then install the cap.

Do not overfill.

4. Wipe up any fuel that may have spilled to prevent a

fire hazard.

22

Содержание workman HDX-D 07368





























































Отзывы: