Toro 34231 Скачать руководство пользователя

Страница: 68 / 84

g313362

Figure 98

Left motion-control rod

Jam nut

Right motion-control rod

Jam nut (rod adjustment)

Ball joint

Adjust the motion-control rod as follows:

•

To increase the gap between the speed
bar and motion control lever, rotate the
motion-control rod counterclockwise.

•

To decrease the gap between the speed
bar and motion control lever, rotate the
motion-control rod clockwise.

Tighten the jam nuts (

Figure 98

Repeat steps

through

for the other motion

control lever.

Install the knee pad; refer to

Installing the Knee

Pad (page 50)

Adjusting the Motion
Control Tracking

If the machine travels or pulls to one side when the
motion-control levers are in the full forward position,
adjust the tracking.

While driving the machine across a flat field,
push both control levers forward the same
distance.

Check if the machine pulls to one side, stop the
machine, shut off the engine, and engage the
parking brake.

Loosen the 2 jam nuts that secure the
motion-control rod at the upper and lower ball
joints (

Figure 99

g313362

Figure 99

Left motion-control rod

Jam nut

Right motion-control rod

Jam nut (rod adjustment)

Ball joint

Adjust the motion-control rod as follows:

•

To increase the speed for the drive, rotate
the motion-control rod counterclockwise in
1/4 turn.

•

To decrease the speed for the drive, rotate
the motion-control rod clockwise in 1/4 turn.

Tighten the jam nuts (

Figure 99

Repeat steps

through

until the machine

tracks straight when the motion-control levers
are in the full forward position.

Содержание 34231





















































































Результаты поиска

Содержание 34231

Отзывы:

Похожие инструкции для 34231

Бренды по названию

Популярные бренды

Toro 34231, Руководство оператора

Результаты поиска

Содержание 34231

Отзывы:

Похожие инструкции для 34231

Бренды по названию

Популярные бренды