Toro 34231 Скачать руководство пользователя

Страница: 52 / 84

Lubricating the Caster-Axle
Bearings

Service Interval:

Yearly

Prepare the machine for maintenance; refer to

Preparing the Machine (page 49)

Connect a grease gun to the fitting in the hub of
the caster wheel (

Figure 66

g314064

Figure 66

Grease fitting (caster-wheel hub)

Pump grease into the fittings until grease begins
to come out of the bearings.

Wipe up any excess grease.

Repeat steps

through

at the other caster

wheel.

Greasing the Belt Tensioner

Service Interval:

Monthly

Prepare the machine for maintenance; refer to

Preparing the Machine (page 49)

At the bottom of the machine, wipe the grease
fittings at belt tensioner pivot clean with a rag
(

Figure 67

g312854

Figure 67

Connect a grease gun to the fittings (

Figure 67

Pump grease into the fittings until grease begins
to come out of the bushings.

Wipe up any excess grease.

Содержание 34231





















































































Результаты поиска

Содержание 34231

Отзывы:

Похожие инструкции для 34231

Бренды по названию

Популярные бренды

Toro 34231, Руководство оператора

Результаты поиска

Содержание 34231

Отзывы:

Похожие инструкции для 34231

Бренды по названию

Популярные бренды