Toro 34231 Скачать руководство пользователя

Страница: 67 / 84

Tighten the 2 knobs that secure the speed bar
(

Figure 95

Adjusting the
Motion-Control Linkage

Prepare the machine for maintenance; refer to

Preparing the Machine (page 49)

Loosen the 2 knobs that secure the speed bar,
and push the speed bar forward (

Figure 96

g313360

Figure 96

Knobs

Speed bar

Push the motion-control lever forward, and
measure the distance between the speed bar
and motion control lever (

Figure 97

Note:

The motion-control linkage is correctly

adjusted when the gap between the lever and
bar is 79 to 87 mm (3-1/8 to 3-7/16 inches).

g313359

Figure 97

79 to 87 mm (3-1/8 to
3-7/16 inches)

More than 87 mm (3-7/16
inches)

Less than 79 mm (3-1/8
inches)

If the gap is larger than or smaller than 79 to 87
mm (3-1/8 to 3-7/16 inches), remove the knee
pad; refer to

Removing the Knee Pad (page 49)

Loosen the 2 jam nuts that secure the
motion-control rod at the upper and lower ball
joints (

Figure 98

Содержание 34231





















































































Результаты поиска

Содержание 34231

Отзывы:

Похожие инструкции для 34231

Бренды по названию

Популярные бренды

Toro 34231, Руководство оператора

Результаты поиска

Содержание 34231

Отзывы:

Похожие инструкции для 34231

Бренды по названию

Популярные бренды