Toro 34231 Скачать руководство пользователя

Страница: 16 / 84

g311618

Figure 11

Spray-pump switch

Spray Wand

g311619

Figure 12

Trigger lock

Spray wand handle

Spray wand trigger

Spray tip

Spray Wand Trigger

Squeeze the trigger (

Figure 12

) to the handle to spray;

release the trigger to stop.

Spray Wand Trigger Lock

Squeeze the trigger against the handle and push
trigger lock (

Figure 12

) forward to keep the wand in

the O

PEN

position. Pull the lock back to release the

trigger.

Specifications

Overall width

left and right booms
extended

161.2 cm (63-1/2
inches)

left and right booms
folded

91.4 cm (36
inches)

Overall length

179.4 cm (70-5/8
inches)

Overall height

128.2 cm (50-1/2
inches)

Weight

sprayer tank and
hopper empty

376 kg (829 lb)

only hopper full

430 kg (949 lb)

only sprayer tank
full

467 (1029 lb)

sprayer tank and
hopper empty and
1 extra bag of
granular material
in the tank

399 kg (879 lb)

Maximum
machine weight

loaded m
operator

658 kg (1450 lb)

Hopper capacity

54 kg (120 lb)

Spreader cast

0.9 m (3 ft)
through 7.6 m
(25 ft)

Sprayer tank
capacity

left or right

91 L (24 US
gallon)

left or right boom

61 cm (2 ft)

Spray Width

center boom

122 cm (4 ft)

Maximum Spray
Width

244 cm (8 ft)

forward

13 kph (8 mph)

Maximum ground
speed

reverse

6 kph (4 mph)

Содержание 34231





















































































Результаты поиска

Содержание 34231

Отзывы:

Похожие инструкции для 34231

Бренды по названию

Популярные бренды

Toro 34231, Руководство оператора

Результаты поиска

Содержание 34231

Отзывы:

Похожие инструкции для 34231

Бренды по названию

Популярные бренды