Toro 30667 Скачать руководство пользователя страница 7

g034338

Figure 9

1.

Nut (5/16 inch)

4.

Headlight bracket

2.

Washer

5.

Bracket tab

3.

Spacer

6.

Bolt (5/16 x 1-5/8 inch)

4.

Fasten the left and right headlight assemblies
to the headlight brackets (

Figure 7

with the

fasteners supplied in the kit.

Note:

Ensure that the turn-signal lens on the

headlight is positioned toward the outside of the
traction unit.

5.

Tighten the locknut to firmly hold the headlight
assembly to the headlight-assembly bracket.

Note:

Do not overtighten the locknut.

Note:

You cannot use the front and rear cab lights for

CE applications. Disable the front and rear cab lights
as follows:

Front

—Remove the lights from the cab roof and

disconnect the wires from the lights. Install the
lights into the cab.

Rear

—Remove the screws securing the lenses to

the lights. Remove the bulbs from the lights and
install the lenses to the lights.

4

Installing the Horn

Parts needed for this procedure:

1

Horn

1

Horn bracket

1

Bolt (3/8 x 5/8 inch)

1

Flange nut (3/8 inch)

2

Bolt (1/4 x 2 inches)

2

Nut (1/4 inch)

Procedure

1.

Secure the horn strap to the horn bracket with a
bolt (3/8 x 5/8 inch) and a flange nut (3/8 inch)
as shown in

Figure 10

.

g023184

Figure 10

1.

Horn bracket

2.

Horn strap

2.

Mount the horn bracket to the back side of the
roller-support tube with 2 bolts (1/4 x 2 inches)
and nuts (1/4 inch). Rotate the horn so that it
faces down (

Figure 10

).

7

 

Содержание 30667





















Отзывы: