Toro 30667 Скачать руководство пользователя страница 5

Drilling the Mounting Holes in the
Rear Bumper for the License Plate

Using the dimensions shown in

Figure 5

locate and

drill 2 holes (9/32 inch) through the outside wall of the
rear bumper.

g029755

Figure 5

1.

8.3 cm (3-1/3 inches)

3.

52.07 cm (20-1/2 inches)

2.

13.3 cm (5-1/4 inches)

4.

Drill a hole (9/32 inch)
here.

3

Installing the Headlights

Parts needed for this procedure:

1

Right headlight bracket

1

Left headlight bracket

6

Bolt (3/8 x 2-1/2 inches)

6

Flange nut (3/8 inch)

8

Washer (3/8 x 7/8 inches)

2

Rubber hanger

4

Spacer

4

Bolt (5/16 x 1-5/8 inches)

4

Flange nut (5/16 inch)

1

Right headlight assembly

1

Left headlight assembly

2

Bent-plate bracket

Installing the Headlight Bracket to
a ROPS Model

1.

Fasten the left and right headlight brackets to
the front of the roller-support tube with 6 bolts
(3/8 x 2-1/2 inches) and 6 flange nuts (3/8 inch)
as shown in

Figure 6

.

g029788

Figure 6

1.

Installed headlight bracket

3.

Headlight bracket

2.

Bolts (3/8 x 2-1/2 inches)

4.

Flange nuts (3/8 inch)

Note:

Position the bolts so that the flange nuts

are toward the front of the traction unit.

2.

Fasten the left and right headlights to the
headlight brackets (

Figure 7

with the fasteners

supplied with the lights.

5

 

Содержание 30667





















Отзывы: