Toro 30667 Скачать руководство пользователя страница 14

g023200

Figure 25

1.

Self-tapping screws (#8 x
1/2 inch)

3.

Junction block

2.

Ground-block terminal

4.

Wire harness fuse block

5.

Connect the large-ring terminal, from the wire
harness, to the stud on the junction block (

Figure

25

).

6.

Install the compartment clamp and seal to the
traction unit with the flange-head screw (

Figure

23

).

7.

Route the front end of the wire harness under
the operator platform to the front of the traction
unit (

Figure 26

).

g311790

Figure 26

1.

Jumper wire harness
for machines with LED
headlights

3.

Connectors for headlights

2.

Brake connector for
machines with halogen
headlights

4.

Horn connectors

Note:

Use

Figure 27

or

Figure 15

to determine

which headlight you have.

8.

For machines with LED headlights, install the
jumper wire harnesses shown in

Figure 26

.

9.

Thread each harness connector through the
appropriate headlight bracket and connect it to
the headlight (

Figure 26

).

10.

Plug the wire harness lead, with the 2
connectors, into the horn (

Figure 26

).

11.

Position the platform shroud on top of the frame
(

Figure 27

).

12.

Plug the light-kit wire harness connectors into
the shroud headlights (

Figure 27

).

14

 

Содержание 30667





















Отзывы: