Toro 30667 Скачать руководство пользователя страница 13

11

Installing the Wire Harness

Parts needed for this procedure:

1

Wire harness

1

Switch-panel-enclosure cover

3

Screw (#10 x 1/2 inch)

3

Mounting pad

11

Cable tie

2

Jumper wire harness (LED headlights only)

Procedure

Use the following instructions and illustrations to route
and connect the wire harness.

g034565

Figure 22

1.

Remove the flange-head screw securing the
compartment clamp and seal to the traction unit
(

Figure 23

).

Note:

Remove the clamp and seal to gain

access to the fuse compartment.

g023198

Figure 23

1.

Compartment clamp

2.

Seal

2.

From under the right side of the traction
unit, route the fuse-block section of the wire
harness up to and into the opening in the fuse
compartment (

Figure 24

).

g029803

Figure 24

Important:

When routing the wire harness,

do not pull it across sharp edges, which may
damage the wires. Wires must not contact
hot or moving parts. Secure the wire harness
with cable ties.

3.

Mount the wire-harness-fuse block next to the
existing fuse block with the 2 self-tapping screws
(#8 x 1/2 inch) included with the wire harness
(

Figure 25

).

Note:

Do not overtighten the screws.

4.

Connect the small-ring terminal from the wire
harness to 1 of the screws on the ground-block
terminal (

Figure 25

).

13

 

Содержание 30667





















Отзывы: