Toro 30667 Скачать руководство пользователя страница 10

2.

Insert the cable tie through the slots in the
column mount bracket so that the ends are
outward, but do not tie them.

3.

Install the steering-column bracket onto the
steering column with the mounting bracket, 2
carriage bolts, and 2 flange nuts (

Figure 14

).

Important:

Ensure that the top of the

steering-column bracket is 21 mm (0.83 inch)
below the top of the steering column.

Important:

Torque the fasteners to 19 to 24

N∙m (14 to 18 ft-lb). Do not overtighten the
carriage bolts; otherwise, you may deform
the steering-column bracket.

8

Installing the Brake-Sensor
Bracket

Parts needed for this procedure:

1

Carriage bolt (#10 x 5/8 inch)

1

Locknut (#10)

1

Sensor plate

2

Flange nut (1/4 inch)

1

Brake-sensor bracket

2

Bolts (1/4 x 3/4 inch)

2

Slotted screw (#6 x 1 inch)

4

Washer (#6)

1

Brake sensor

2

Locknut (#6)

Procedure

Note:

This procedure is only for machines with

halogen headlights. Use

Figure 15

to determine if you

have halogen headlights.

g312027

Figure 15

1.

Halogen headlight

2.

LED headlight

1.

Disassemble the proximity-sensor assembly on
the brake-pedal lever (

Figure 16

) and set aside

all the parts except the proximity sensor.

g029761

Figure 16

1.

Forward footrest

4.

Proximity sensor

2.

Carriage bolt (#10 x 5/8
inch)

5.

Brake-pedal lever

3.

Brake-sensor plate

6.

Locknut (#10)

2.

Assemble the proximity-sensor assembly to the
brake lever using the carriage bolt (#10 x 5/8
inch), brake-sensor plate, proximity sensor, and
locknut (#10) as shown in

Figure 16

.

Note:

Ensure that you do not overtighten the

bolts. Overtightening the bolts will damage the
sensor.

3.

Locate the brake-sensor bracket mounting holes
on the front footrest and loosely install the
brake-sensor bracket to the front footrest using 2
bolts (1/4 x 3/4 inch) and 2 flange nuts (1/4 inch).

Note:

You will need to move the brake-sensor

bracket up or down to align the brake sensor to
the brake-sensor plate (

Figure 17

).

10

 

Содержание 30667





















Отзывы: