Toro 30667 Скачать руководство пользователя страница 11

g029762

Figure 17

1.

Forward footrest

5.

Brake-sensor bracket

2.

Slotted screw (#6 x 1 inch)

6.

Locknut (#6)

3.

Washer (#6)

7.

Bolts (1/4 x 3/4 inch)

4.

Brake sensor

8.

Flange nut (1/4 inch)

4.

Loosely install the brake sensor to the
brake-sensor bracket with the 2 slotted screws
(#6 x 1 inch), 2 washers, and 2 flange nuts
(

Figure 17

).

5.

Align the brake sensor in or out and the
brake-sensor bracket up or down so that the
switch on the brake sensor is pressing against
the sensor plate.

6.

Complete the brake-sensor assembly installation
by tightening all of the mounting hardware.

Tighten the 2 slotted screws (#6 x 1 inch)
and 2 flange nuts to firmly secure the brake
sensor to the brake-sensor bracket.

Note:

Ensure that you do not overtighten

the screws. Overtightening the screws will
damage the sensor.

Tighten the bolts (1/4 x 3/4 inch) and 2 flange
nuts (1/4 inch) holding the brake-sensor
bracket to the front footrest to 1,017 to 1,243
N∙cm (90 to 110 in-lb).

Important:

After you complete the installation of

the light kit, verify that the brake sensor activates
the brake lights when the brake pedal is pressed.
Realign the brake sensor if necessary.

9

Installing the Rear Lamps

Parts needed for this procedure:

1

Left light bracket

1

Right light bracket

4

Screw (5/8 x 3 inches)

4

Flat washer

2

Jam nut (5/8 inch)

2

Rear-lamp assembly

Procedure

1.

Remove the 2 bolts, 2 washers, and 2 nuts
securing the reservoir-mounting bracket to the
left frame rail (

Figure 18

).

Note:

Stabilize the reservoir and bracket to

prevent them from falling.

g023193

Figure 18

1.

Reservoir bracket mounting bolts, washers, and nuts

2.

Secure the left light bracket to the bracket and
frame with 2 bolts (5/8 x 3 inches), 2 flat washers
and 2 jam nuts as shown in (

Figure 19

).

11

 

Содержание 30667





















Отзывы: