Toro 04060 Greensmaster 1600 Скачать руководство пользователя страница 13

Страница: 13 / 24

+/" '" .0-" .,-' ,(0$ 1&-" &. &*./(("! +*

.,-' ,(0$

Make sure traction (Fig. 18) and reel drive (Fig. 19)

levers are in DISENGAGED position.

+/"

Engine will not start if traction lever is in the

engaged position.

Open fuel shutĆoff valve on engine (Fig. 20).

Move ON / OFF switch (Fig. 21 ) to ON position .

Move throttle control (Fig. 18) to FAST position.

Move choke lever (Fig. 20) to halfĆopen position

when starting a cold engine. Choke may not be

required when starting a warm engine.

Pull recoil starter handle out until positive

engagement results, then pull vigorously to start

engine. Close choke as engine warms up.

+/" + *+/ ,0(( -" +&( -+," /+ &/. (&)&/ +- ("/ $+ +#

./-/"- %*!(" 1%"* -+," &. ,0(("! +0/ " 0."

-+," )2 -"' +- -" +&( ..")(2 )2 "

!)$"!

To stop engine during operation, move traction

and reel drive controls to DISENGAGED position,

throttle control to SLOW and ON/OFF switch to OFF.

Pull spark plug wire off spark plug to prevent the

possibility of accidental starting before storing

machine.

Close fuel shutĆoff valve before storing or

transporting mower in a vehicle.

Push kick stand down with foot and pull up on

handle to raise rear of mower and install transport

wheels.

To release kickstand, pull up on handle, push

mower forward and then lower rear of mower onto

transport wheels.

Assure traction and reel drive controls are in

DISENGAGE position and start engine.

Set throttle control to SLOW, tip front of machine up

gradually engage traction drive and slowly increase

engine speed.

Adjust throttle to operate mower at desired ground

speed and transport mower to desired destination.

Return traction control lever to DISENGAGE,

throttle to SLOW and stop engine.

Push kickstand down with foot and pull up on

handle to raise wheels off the ground.

Push locking clips on wheels out of grooves in

shafts and slide wheels off shafts.

Release kickstand.

Proper use of the Greensmaster 1600 provides the

smoothest turf cutting available. The fundamental

suggestions given will provide the utmost performance

from your mower.

Remove dew and worm casts from turf prior to mowing

by whipping the turf with a bamboo pole or by dragging

a hose over the area. Be sure the mower is carefully

adjusted and is set evenly on both sides of the reel.

Improper mower adjustment is magnified many times

over in the appearance of the clipped turf. A

threeĆtoĆfive foot wide collar" should be mowed

around the area at a slightly higher cut than the putting

green area. This will provide sufficient space for turning

the mower without turning on the green area.

The Greens should be mowed in a straight back and

forth direction across the green. Avoid circular mowing

or turning the mower on greens areas since scuffing

may occur. Turning the mower should be done off the

green proper by raising the cutting reel (pushing the

handle down) and turning on the traction drum. The

greens area should not be mowed in the same

direction at any two successive mowings. Cutting in

different directions at each mowing will keep the grass

growing in an upright position, preventing grain

formation. Mowing should be done at a normal walking

pace. Fast speeds saves very little time and will result in

an inferior mowing job.

Содержание 04060 Greensmaster 1600

























Результаты поиска

Содержание 04060 Greensmaster 1600

Отзывы:

Похожие инструкции для 04060 Greensmaster 1600

Бренды по названию

Популярные бренды

Toro 04060 Greensmaster 1600, Руководство оператора

Результаты поиска

Содержание 04060 Greensmaster 1600

Отзывы:

Похожие инструкции для 04060 Greensmaster 1600

Бренды по названию

Популярные бренды