TLV COSPECT M-COS-16 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 36

background image

172-65188M-08 (

M-COS 3,16,21

Pressure Reducing Valve) 24 Jun 2015

24

Disassembling the Piston Section

Remove the pilot body after loosening and removing the bolts.
During this process, pay attention not to lose the connecting tubes (2).

Remove the piston, cylinder and the silencer (for 65 – 100 mm only) from the main
body. Then remove the piston rings and the tension rings from the piston. Do not
apply too much force when removing the piston rings and tension rings.

→Check for the interior of the cylinder, the exterior of the piston rings, the small hole

on the piston and the gaskets for any fault or abnormality.

15 – 50 mm

Piston Ring

Tension Ring

Piston Ring

Tension Ring

Piston

Connecting Tube

Cylinder Gasket

Cylinder

Pilot Cover Gasket

Piston Ring

Tension Ring

Piston Ring

Tension Ring

Piston

Connecting Tube

Cylinder

Pilot Cover Gasket

Seal Ring

Silencer

65 – 100 mm

«
...
23
24
25
26
27
...
»

Содержание COSPECT M-COS-16





































Отзывы:

Нет отзывов

Похожие инструкции для COSPECT M-COS-16

Бренд: ABB Страницы: 138

Бренд: ABB Страницы: 116

Relion 615 series

Бренд: ABB Страницы: 136

Бренд: Samson Страницы: 36

Бренд: FBII Страницы: 71

Бренд: CAME Страницы: 4

Бренд: Garmin Страницы: 12

Бренд: Bang & Olufsen Страницы: 36

Бренд: Mad Catz Страницы: 4

Бренд: Caen Страницы: 20

Бренд: Dahua Страницы: 58

Бренд: Kamstrup Страницы: 36

Бренд: JFA Electronicos Страницы: 29

Бренд: National Instruments Страницы: 2

Бренд: Panamax Страницы: 16

Бренд: Watts Страницы: 24

Z3-DM8107-SDI-RPS

Бренд: Z3 Technology Страницы: 73

Бренд: Z-Wave Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды