TLV COSPECT M-COS-16 Скачать руководство пользователя страница 22

Страница: 22 / 36

172-65188M-08 (

M-COS 3,16,21

Pressure Reducing Valve) 24 Jun 2015

Maintenance

Take measures to prevent people from coming into direct contact with

product outlets. Failure to do so may result in burns or other injury from

the discharge of fluids.

CAUTION

Be sure to use only the recommended components when repairing the

product, and NEVER attempt to modify the product in any way. Failure to

observe these precautions may result in damage to the product or burns

or other injury due to malfunction or the discharge of fluids.

CAUTION

Make sure the power supply switch is OFF before carrying out work on

the wiring or inspections involving disassembly.

If such work is carried out with the power on, there is a danger that

equipment may malfunction or electric shock may occur, leading to

injury or other accidents.

CAUTION

Make sure that wiring work requiring a special license is carried out by

qualified personnel.

If carried out by unqualified personnel, overheating or short circuits

leading to injury, fires, damage or other accidents may occur.

CAUTION

When using this product, NEVER stand close to, or leave tools anywhere

near moving parts, such as the shaft.

Contact with moving parts or objects becoming caught in moving parts

could lead to injury, damage or other accidents.

CAUTION

Operational Check

To ensure long service life of the

M-COS

, the following inspection and maintenance

should be performed regularly.

Part

Inspection and Maintenance Frequency

Screens
(Separator, Pilot)

Disassemble and clean annually.

If there is substantial blockage, install a strainer
(approximately 60 mesh) ahead of the

M-COS

Main Valve, Main Valve
Seat, Pilot Valve and
Pilot Valve Seat

Replace after approximately 15,000 hours.

If there is chattering or dirt, premature wear may result.

Piston Ring

Replace after approximately 8,000 hours.

If there is chattering or if scale build-up is severe, premature
wear may result.

Piston

Replace after approximately 30,000 hours.

If hunting or chattering takes place, premature wear may
result.

Trap Valve Seat

Replace after approximately 40,000 hours.

If scale build-up is severe, blockage may occur in a short
period of time.

Diaphragm

Replace after approximately 30,000 hours.

If hunting or chattering takes place, cracks or fatigue may
develop in a short period of time.

Содержание COSPECT M-COS-16





































Результаты поиска

Содержание COSPECT M-COS-16

Отзывы:

Похожие инструкции для COSPECT M-COS-16

Бренды по названию

Популярные бренды

TLV COSPECT M-COS-16, Инструкция по эксплуатации

Результаты поиска

Содержание COSPECT M-COS-16

Отзывы:

Похожие инструкции для COSPECT M-COS-16

Бренды по названию

Популярные бренды