TLV COSPECT M-COS-16 Скачать руководство пользователя страница 12

Страница: 12 / 36

172-65188M-08 (

M-COS 3,16,21

Pressure Reducing Valve) 24 Jun 2015

Installation

Install properly and DO NOT use this product outside the recommended

operating pressure, temperature and other specification ranges.

Improper use may result in such hazards as damage to the product or

malfunctions which may lead to serious accidents. Local regulations

may restrict the use of this product to below the conditions quoted.

CAUTION

Use hoisting equipment for heavy objects (weighing approximately

20 kg or more). Failure to do so may result in back strain or other injury if

the object should fall.

CAUTION

Take measures to prevent people from coming into direct contact with

product outlets. Failure to do so may result in burns or other injury from

the discharge of fluids.

CAUTION

Make sure the power supply switch is OFF before carrying out work on

the wiring or inspections involving disassembly.

If such work is carried out with the power on, there is a danger that

equipment may malfunction or electric shock may occur, leading to

injury or other accidents.

CAUTION

Make sure that wiring work requiring a special license is carried out by

qualified personnel.

If carried out by unqualified personnel, overheating or short circuits

leading to injury, fires, damage or other accidents may occur.

CAUTION

When using this product, NEVER stand close to, or leave tools anywhere

near moving parts, such as the shaft.

Contact with moving parts or objects becoming caught in moving parts

could lead to injury, damage or other accidents.

CAUTION

Installation, inspection, maintenance, repairs, disassembly, adjustment and valve
opening/closing should be carried out only by trained maintenance personnel.

1. Blowdown

Before installing the

M-COS

, be

sure to blow down all piping
thoroughly. If this is not possible,
perform a blowdown using the
bypass valve.

Blowdown is especially important
for newly installed piping or after
the system has been shut down
for a long period of time.

Open

Closed

Blowdown using bypass valve

M-COS

2. Removing Seal and Cap







Before installation, be sure to remove all protective

seals and caps.
(Found in 3 locations, on the product inlet and outlets.)

3. Installation Angle

Install the

M-COS

vertically, so that the

arrow mark on the body points horizontally
in the direction of steam flow.

Allowable inclination is 10 degrees in the
fore-aft direction and 15 degrees in the
plane perpendicular to the steam flow line.

Содержание COSPECT M-COS-16





































Результаты поиска

Содержание COSPECT M-COS-16

Отзывы:

Похожие инструкции для COSPECT M-COS-16

Бренды по названию

Популярные бренды

TLV COSPECT M-COS-16, Инструкция по эксплуатации

Результаты поиска

Содержание COSPECT M-COS-16

Отзывы:

Похожие инструкции для COSPECT M-COS-16

Бренды по названию

Популярные бренды