manualshive.com logo in svg

TLV COSPECT M-COS-16, Инструкция по эксплуатации

Поделиться
Скачать
TLV COSPECT M-COS-16 Скачать руководство пользователя страница 2

 

172-65188M-08  (

M-COS  3,16,21

  Pressure  Reducing Valve)   24 Jun 2015

 

1

 

Contents 

 

Introduction ........................................................................ 1

 

Safety Considerations ........................................................ 2

 

Specifications ..................................................................... 4

 

Acceptable Operating Range ............................................. 6

 

Correct Usage of the 

M-COS

 Motorized Pressure 

Reducing Valve .................................................................. 7

 

Configuration ...................................................................... 9

 

Installation ........................................................................ 11

 

Controller Operation ......................................................... 18

 

Maintenance ..................................................................... 21

 

Disassembly ..................................................................... 22

 

Reassembly ..................................................................... 31

 

Troubleshooting ............................................................... 32

 

Product Warranty ............................................................. 35

 

 

 
Introduction 

 

Thank you for purchasing the

 

M-COS

 motorized pressure reducing 

valve for steam. 

This product has been thoroughly inspected before being shipped from the 
factory. When the product is delivered, before doing anything else, check the 
specifications and external appearance to make sure nothing is out of the 
ordinary. Also be sure to read this manual carefully before use and follow the 
instructions to be sure of using the product properly. 

The

  motorized pressure reducing valve for steam, model 

M-COS

 is a 

high performance motor actuated remote type pressure reducing valve 
adding a remote control function to the

 

 

COS 

pressure reducing valve. It 

can be easily adjusted by remote to supply dry saturated steam to the 
process at the set pressure as needed without fluctuation, thus improving 
steam use and contributing to the improvement of energy effeciency, 
productivity and product quality.

.

 

If detailed instructions for special order specifications or options not 
contained in this manual are required, please contact 

  for full details. 

This instruction manual is intended for use with the model(s) listed on the 
front cover. It is needed not only for installation, but also for subsequent 
maintenance, disassembly/reassembly and troubleshooting. Please keep it in 
a safe place for future reference. 

Содержание COSPECT M-COS-16





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды