manualshive.com logo in svg

TLV COSPECT M-COS-16, Инструкция по эксплуатации

Поделиться
Скачать
TLV COSPECT M-COS-16 Скачать руководство пользователя страница 15

 

172-65188M-08  (

M-COS  3,16,21

  Pressure  Reducing Valve)   24 Jun 2015

 

14

 

 

11.  Accessories 

  Always install a shut-off valve, pressure gauge and bypass lines at both inlet 

and outlet. 
Ball valves, which will not retain condensate, are recommended for inlet and 
outlet shut-off valves. The bypass pipe should be at least 

1

/

2

 of the size of the 

inlet (primary side) pipe. 

M-COS

 has a built-in strainer, however in case an external strainer is installed, 

it should be installed ahead of 

M-COS

 and the strainer should be installed 

horizontally with the basket at the 3 or 9 o’clock position in order to prevent 
condensate accumulation. 

Ball Valve

Ball Valve

Glove Valve

M-COS

Pressure
Gauge

Pressure

Gauge

M-COS

 

12.  Installation of the Controller Unit 

  Mount the controller unit securely on a wall, etc. with self-tapping screws 

inserted in the holes.   
The controller is not waterproof. Be sure to install it indoors in a suitable 
protected area.   
The ambient temperature range specified for the normal operation of the unit is 
between 0 and 50 °C. Avoid operation beyond this specified range.   
Install the controller unit in a suitable place with low humidity and vibration. 

13.  Installation of the Pressure Sensor 

  Install the pressure sensor on or near the steam using equipment on the piping. 

Arrange the piping as perpendicularly as practical with the siphon tube 

supplied. (Direct mounting of the sensor to the equipment or to the piping may 
result in damage to the pressure sensor due to conduction of heat.) 

NOTE: The pressure sensor is made to withstand a maximum pressure of 
2 times the maximum value of the measurement range.   
If there is a possibility that excessive pressure beyond this limit will be 
applied to the sensor due to water hammer or otherwise, consult our sales 
staff before continuing the installation. 

 

Содержание COSPECT M-COS-16





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды