background image

POLE HEDGE TRIMMER 400W  TTB427GTM

MAINTENANCE

 

WARNING!

 Before carrying out any repairs or servicing 

work, you must ensure that the pole hedge trimmer has 
been  disconnected  from  the  power  supply.  Repairs  and 
maintenance  work  other  than  described  within  this 

instruction manual may be performed only by qualified specialist!

1. SERVICE 

To  ensure  long  and  reliable  service,  carry  out  the  following 
maintenance regularly. Servicing and cleaning work on the pruner 
and  the  removal  of  the  guards  may  only  be  carried  out  after  the 
motor has been switched off and the plug disconnected from the 
power supply.

1). Keep the product clean. Remove debris from it after each use and 
before storage.

2). Regularly check for obvious defects such as loose, dislodged or 
damaged blade, loose fixings and worn or damaged components.

3). Clean the product with a dry cloth. Use a brush for areas that are 
hard to reach.

4). In particular clean the air vents after every use with a cloth and 
brush.

5). Clean the pole hedge trimmer with a brush or cloth. Do not use 
any solvents or water to remove dirt. Remove stubborn dirt with high 
pressure air (max. 3 bar).

6). Do not clean the pole hedge trimmer while it is running.

7). Ensure that all the fastening elements (screws, nuts, etc.) are tight 
at all times so that you can safely work with the pole hedge trimmer.

8).  Check  the  pole  hedge  trimmer  frequently  for  signs  of  wear. 
Replace worn or damaged parts.

9). Store your pole hedge trimmer in a dry place. To ensure a long 
service life all screw parts should be cleaned and then oiled.

10). The component that is subject to most wear is the cutting blade. 
You should therefore check the condition of the cutting blade and its 
mounting at regular intervals.
- If the cutting blade is worn or blunt it must be replaced immediately;
- If the pole hedge trimmer starts to suffer from excessive vibrations, 
this means that the cutting blade has suffered deformation due to 
impacts. In this case it must be repaired or replaced.

400w 高枝.indd   21

12-3-2   上午11:36

Содержание TTB427GTM



























Отзывы: