Tippmann 98 Custom Platinum Series Basic Скачать руководство пользователя страница 8

Страница: 8 / 40

E
N

S
H

E-Trigger

Operating Instructions (continued from page 11)

counterclockwise to increase

rate of fire to the

desired speed.

clockwise
to slow the
rate of fire.

Tuning - Troubleshooting B:
If the trigger remains easy to pull after adjusting the flow control, there
may be a leak in the system. Double check installation making sure all
fittings are tight and o-rings are properly seated. If you need to
disassemble to check that all fittings are tight and o-rings are properly
seated (see Response

parts below), do not disassemble this marker

Tuning - Troubleshooting A:
If tuning the Response

Trigger produces little or no response in the

rate of fire, reset the Flow Control as follows:
1) With marker properly unloaded (see page 21), begin adjusting rate of
fire by turning flow control clockwise

completely (Do not over tighten

or damage will occur). In a safe direction fire 2 to 4 shots. Trigger should
become very hard to pull or even unable to be pulled. If this occurs, the
response trigger system is functioning properly. Go to step 2. If it does
not occur, go to Troubleshooting B.
2) Now while firing in a safe direction with marker still unloaded, slowly
turn the flow control adjustor counterclockwise

until desired rate of

fire is achieved.

NOTE: To disable the Response

System:

❏

First follow the

unloading and air supply removal
instructions on page 20 and never
disassemble a marker that is under
pressure.

❏

Remove the banjo

fitting (20-20) attached to the power
tube/valve and replace it with the
shut off plug

(TA05021).

With a screwdriver, turn the Flow Control Adjustor to the desired speed.

TUNING THE RESPONSE

TRIGGER RATE OF FIRE

another trigger pull. This time is measured in milliseconds. (The default Debounce

setting is 20ms). If the marker has been double firing, increase the Debounce

time. To make your marker fire faster, reduce the trigger response time by
decreasing the Debounce

time. To adjust the Debounce

time:

❏

Perform

STEP 3 1) then

❏

select the Debounce

programming feature (= Solid Green

LED),

❏

pull and hold trigger until LED light goes out and

❏

release the trigger.

When LED comes back on -

❏

count the number of green flashes to determine

the current setting and once the LED stops flashing, you have 5 seconds to
begin

❏

pulling and releasing the trigger once for every FULL 1 ms of time you

want the Debounce

to be. On each pull of the trigger, the LED will light up red

(indicating that the pull has been detected). Once you have pulled and released
the trigger the number of times necessary to set the function,

❏

wait a few

seconds for Programming Verification (See Programming Verification on page 11).

THE RATE OF FIRE (ROF) CAP troubleshooting and tuning/programming:
(ROF) Cap sets the maximum cycle speed of the marker. (The default ROF
Cap is 15 bps). Setting this value too low will reduce the usable speed of the
marker. Setting this value too high can cause misfires and “chops” if the hopper
can not keep up. To adjust the Rate of Fire cap:

❏

Perform STEP 3 1) then

❏

select the (ROF) programming feature (=Flickering Green LED),

❏

pull and

hold trigger until LED light goes out and

❏

release the trigger. When LED

comes back on -

❏

count the number of green flashes to determine the current

setting and once the LED stops flashing, you have 5 seconds to begin

❏

pulling

and releasing the trigger once for every bps you want the Rate of Fire (ROF) cap
to be. For example, 20 pulls/releases would be 20 bps. On each pull of the
trigger, the LED will light up red (indicating that the pull has been detected).
Once you have pulled and released the trigger the number of times necessary to
set the function,

❏

wait a few seconds for Programming Verification (See

Programming Verification on page 11).

To Perform A Complete E-Trigger

Reset To the Default Settings:

With the E-Trigger turned off, press and hold the power button for 10 full seconds
as the LED turns on solid orange and at 10 seconds it turns solid red. At this
point, you release the power button and the LED will turn off and the board will
be reset to the factory default settings. Your marker is now ready for normal
operation with the Factory Default Mode Settings: Firing Mode = Semi-auto (1
pull/release of the trigger fires 1 time); Dwell = 6.0 ms; Debounce

= 20 ms;

Rate of Fire (ROF) Cap = 15 bps.

NOTE: You can increase your 98 Custom

Platinum Series

Basic or 98 Custom

Platinum Series

Pro

rate of fire by

adding a Cyclone

Feeder Adapter to your marker.

The Cyclone

Adapter works well with the E-Trigger