E
N
G
L
I
S
H
E
N
G
L
I
S
H
20
Cleaning & Maintenance
❏
Eye protection designed for paintball use must be worn by the user and
any person within range.
❏
To reduce the chance of accidental discharge: First
follow unloading and air supply removal instructions above and never disassemble a
marker that is under pressure.
• Follow warnings listed on the air supply cylinder for handling and storage.
• Familiarize yourself with instructions listed on air supply cylinder or adaptor.
Contact the air supply cylinder or adaptor manufacturer with any questions.
• Do not use any petroleum based cleaning solvents.
• Do not use any cleaning solvents that come in aerosol cans. NOTE: Petroleum
based products and aerosol products can damage your markers’ o-rings.
• To clean your paintball marker use a damp towel with water to wipe off paint,
Unloading Your Marker
❏
Eye protection designed for paintball use must be worn by the user and
any person within range. To unload your marker:
1)
❏
Install the barrel sleeve (see page 2).
2)
❏
Empty and remove the hopper.
3)
❏
Go to a designated firing area and remove the barrel sleeve.
4)
❏
Point your marker in a safe direction and fire several times to be sure
there are no balls lodged in the chamber and / or barrel. IMPORTANT: Do
not uncock your marker as uncocking your marker may push a ball into the
chamber or down into the barrel in which case the ball will be hidden from view.
5)
❏
Install the barrel sleeve (see page 2).
6)
❏
Visually inspect the chamber for paintballs.
Air Supply Cylinder Removal
❏
Eye protection designed for paintball use must be worn by the user and
any person within range. To remove a charged air supply cylinder:
1)
❏
Follow the Unloading Your Marker instructions above.
2)
❏
Turn the cylinder approximately 3/4 of a turn counterclockwise
or out.
This allows the air supply pin valve to close so that no air will enter the marker.
❏
Point the marker in a safe direction and fire the remaining gas in the marker
by pulling the trigger until the marker stops firing. This may take 4-5 shots.
• If your marker continues to fire, the tank pin valve has not closed yet (because
of the variances in tank pin valve parts, each tank varies slightly on exactly
how far it should be turned) and
❏
you will have to turn the tank
counterclockwise
a little further and repeat this step until the marker does
not fire,
❏
then remove the tank. (If during this step - you turned the tank
and it began to leak before you pulled the trigger, the tank o-ring should be
checked for damage before reassembly.)
3) After air tank is removed,
❏
point & fire the marker in a safe direction until
stored air is completely discharged.
NOTE: Before storing or disassembling be sure to follow
❏
Unloading Your
Marker and
❏
Air Supply Cylinder Removal instructions (see above).
❏
Install barrel sleeve (see page 2).
Cleaning & Maintenance
(continued on page 21)
21
Remove the barrel
. To remove the rear-left side receiver
:
❏
Loosen
the 2 adapter bolts
.
❏
turn the velocity screw (7) in
until it stops.
❏
Unscrew the 5 receiver connection bolts
and
❏
carefully lift the rear-
left side receiver to access the internal parts. NOTE: The Safety
will stay
on the rear-left side receiver
and should be reassembled the same way.
Longest bolt
attaches the front
grip
when
reassembling.
Marker Disassembly / Assembly
❏
Eye protection must be worn during disassembly / assembly.
❏
First follow unloading and air supply removal instructions on page 20. Do not
disassemble a pressurized paintball marker. Do not pressurize a partially
assembled paintball marker. Put the marker in the uncocked position. If your
marker is cocked, pull and hold the bolt cocking handle
back - then pull
the trigger and slowly release the handle forward to uncock the marker.
NOTE: Carefully hand start all threaded parts and do not overtighten
and strip
threaded parts
when assembling.
NOTE : To aid in service and the installation of accessories the Left Side
Receiver is split into 2 parts : ( the Rear-left side receiver
and the Front-
left side receiver
).
• For most repairs, only the Rear-Left side Receiver
needs to be removed.
• Only the Front Sight, Front Sight Spring, Front Sight Pin and Ball Latch require
removal of the Front-left side Receiver. It is not necessary to remove the front
sight pin unless broken or the front sight and / or spring need replaced.
• It is not necessary to remove the tank adapter bolts
for most service.
• The Picatinny Rail
does not need to be removed for regular service. To
remove the Picatinny Rail:
❏
unscrew
the 3 screws securing the
Picatinny Rail to the top of the marker.
oil, and debris. Use Tippmann
®
marker oil or other premium marker oil to maintain
your marker in good working condition. Re-oil with a few drops to the front bolt
o-ring and rear bolt o-ring. Oil the barrel o-ring and air supply valve o-ring.
• To clean the barrel. Depress front sight and tip out feed elbow. Insert
tab of cable squeegee into breach, then pull squeegee through barrel
to remove debris.
Cleaning & Maintenance (continued from page 20)
Marker Disassembly
(continued on page 22)
