THORLABS Blueline LDC2 Series Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 51

background image

5.5 Troubleshooting

LDC2xx / page 29

Is the laser diode installed properly?

Control the connection cable.

Is the laser diode polarity set correctly?

If not change the polarity of the diode or set the polarity switch at the

LDC2xx to opposite polarity.

Is the photo diode connected properly?

Check the connecting cable.

Is the photo diode poled correctly?

If in constant power mode the displayed photodiode current is negative you

must revert the polarity of the photodiode.

Are you using a bias voltage with the photo diode in photocurrent mode?

Change the polarity of the diode for photo element mode or change the po-
larity of the bias voltage source.

Is the desired output power programmed correctly?

Adjust the desired output power P

LD

with the tuning knob.

If you don’t find the error source by means of the trouble shooting list please first
contact the

Thorlabs GmbH-Hotline ( [email protected])

before

sending the

LDC200 for checkup and repair to

Thorlabs GmbH

- Germany.

(refer to section 6.7, “Addresses ” on page 43)

«
...
33
34
35
36
37
...
»

Содержание Blueline LDC2 Series




















































Отзывы:

Нет отзывов

Похожие инструкции для Blueline LDC2 Series

Бренд: Valor Страницы: 20

Бренд: L. G. B. Страницы: 2

Бренд: L-Acoustics Страницы: 36

Бренд: Mamas & Papas Страницы: 24

Бренд: Mamas & Papas Страницы: 24

Бренд: Ublox Страницы: 2

Бренд: u-blox Страницы: 19

Бренд: Click2Enter Страницы: 34

Бренд: Scanreco Страницы: 10

Бренд: Teledyne Страницы: 102

Бренд: Wenglor Страницы: 44

Wattstopper LMIN-104

Бренд: LEGRAND Страницы: 22

Бренд: Flying Industry Development Страницы: 2

Бренд: National Instruments Страницы: 14

Бренд: Sturtevant Richmont Страницы: 73

Cutler-Hammer S701X25N3BP

Бренд: Eaton Страницы: 4

Бренд: Zhejiang Dongma Baby Carrier Страницы: 15

Бренд: Parker Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды