manualshive.com logo in svg

THORLABS Blueline LDC2 Series, Руководство по эксплуатации

Поделиться
Скачать
THORLABS Blueline LDC2 Series Скачать руководство пользователя страница 23

 

3.4 Constant current mode (CONST I)

 

 

LDC2xx / page 17 

 

3.4    Constant current mode (CONST I) 

Switch on the LDC2xx. 
 
Select a suitable current limit "I

LIM

" (refer to chapter 3.2). 

 
Select the appropriate laser polarity (refer to chapter 3.3). 
 
Connect the laser diode (refer to chapter 3.1.3). 
 
Select the display "I

LD

" with the button (L18) or (L19). 

 
Set the adjust knob (L10) completely to the left. 
 
Select constant current mode with key "I" (L23). 
 
Switch  on the output by pressing key "ON"  (L9). The LED "ON" (L8) lights up, the 
output is activated and the curr ent slowly rises (about 1 s) to the set value with knob 
(L10). 
 

NOTE: 

The current output can only be switched on if the jack "LD OUTPUT" (R5) 

is connected correctly. 

 
The display shows the injection current "I

LD

". 

 
With the adjust knob (L10) the laser curr ent can be set continuously between 0 mA 
and the selected current limit "I

LIM

". 

 
If  the injection current "I

LD

"  reaches the set current limit "I

LIM

"  during operation the 

LED  "LIM" (L7) lights up, a short beep as

  warning signal is heard and the laser 

current is limited to the value of the current limit "I

LIM

". 

 
If  the LED "LIM" (L7) lights up noise 

and  ripple do not longer correspond to the 

specifications for normal operation (refer to  chapter 6.3). However exceeding the set 
current limit "I

LIM

" is not possible. 

Содержание Blueline LDC2 Series




















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды