THORLABS Blueline LDC2 Series Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 51

background image

1.1 At a Glance

LDC2xx / page 2

When  turned on the laser diode controller L DC2xx  is automatica lly  in LASER OFF
mode. The laser current can be switched on/off with a separate key at the front panel.

Laser diode and photodiode are connec ted by a 9-pin D-sub jack at the rear of the
unit. The output for the laser diode and the  input for the photodiode  are bipolar, thus
all polarities of commercial available laser diodes can be connected.

With  a control signal at the output jack

an external LED can be used to indicate

LASER ON.

The injection current or the optical output  power of the laser diode can be modulated
via a modulation input at the rear of the unit.

For monitoring purposes a voltage proportional  to the laser diode current is provided
at an analog control output at the rear.

If an error occurs or the limit for the la ser current is reached, the corresponding LED
lights up and a short beep gives a warning.

The  installed mains filter and careful tr ansformer  shielding provide low ripple and
noise at the output.

The internal cooling of the LDC200 with a fan protects the unit against overheating in
case of high environmental temperatures.
With free air circulation a safe operation of the unit is guaranteed up to 40 °C ambient
temperature.

Attention

Do not obstruct the air-ventilation slots in the housing!

If a laser diode head and the corresponding cable (CAB 400) by

Thorlabs GmbH

is

used, damages caused by wrong connections are impossible.

«
...
6
7
8
9
10
...
»

Содержание Blueline LDC2 Series




















































Отзывы:

Нет отзывов

Похожие инструкции для Blueline LDC2 Series

Бренд: Garmin Страницы: 12

Бренд: Aaeon Страницы: 76

Бренд: Acclaim Lighting Страницы: 32

Бренд: Jeep Страницы: 19

Бренд: Abus Страницы: 12

Бренд: Watts Страницы: 12

Бренд: Lancom Страницы: 8

REVOLUTION Pro Controller 2

Бренд: Nacon Страницы: 11

Бренд: Nacon Страницы: 18

Бренд: Nacon Страницы: 24

Бренд: Nabco Страницы: 35

Бренд: Vaillant Страницы: 12

Бренд: Newport Страницы: 417

Бренд: Binder Страницы: 147

Бренд: Netro Страницы: 14

Бренд: Atmel Страницы: 12

Бренд: Jeckson Electric Страницы: 2

Бренд: Pestill Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды