manualshive.com logo in svg

THORLABS Blueline LDC2 Series, Руководство по эксплуатации, Страница: 48 / 51

Поделиться
Скачать
THORLABS Blueline LDC2 Series Скачать руководство пользователя страница 48

6.5 List of acronyms 

 

LDC2xx / page 42 

 

 

6.5  List of acronyms 

The following acronyms are used in this manual: 
 
AC   

Alternating Current 

AG   

Anode Ground 

CC   

Constant Current mode 

CG   

Cathode Ground 

CP   

Constant Power mode 

DC   

Direct Current 

LD 

 

Laser Diode 

LDC   

Laser Diode Controller 

LED   

Light Emitting Diode 

OTP   

Over TemPerature 

PD   

Photo Diode 

TEC   

Thermo Electric Cooler (Peltier Element) 

VCSEL 

Vertical Cavity Surface Emitting Laser 

 
 
 

6.6  List of figures 

 
Figure 1

 

Display- and operating elements at the front panel 

7

 

Figure 2 

 

Operating elements on the rear panel 

8

 

Figure 3

 

Pin assignment of the "LD OUTPUT"jack (female) 

11

 

Figure 4

 

Connecting the interlock with and without monitoring LED 

11

 

Figure 5

 

Connecting laser diode and photodiode 

12

 

Figure 6

 

Connecting laser diode and photodiode 

13

 

Figure 7

 

Changing the mains fuse 

26

 

Figure 8

 

Label ‘Internal fuses’ 

27

 

Figure 9

 

Setting the line voltage 

27

 

Figure 10

 

Crossed out “wheelie bin” symbol 

41

 

 

Содержание Blueline LDC2 Series




















































Отзывы:

Нет отзывов