Thermo Scientific Orion 2111LL Скачать руководство пользователя

Страница: 70 / 118

IV-

Calibration

Thermo Scientific Orion 2111LL Sodium Monitor User Guide

ROSS and the COIL tradedress are trademarks of Thermo Fisher Scientific Inc. US Patent 6,793,787

Stage

User Action

Marquee

Main Display

top line

bottom line

Valve position

Press

System will proceed to measurement

mode

Actual temperature

reading

Actual

readings in

ppb & mV

System enters measurement

mode, but will remain on hold

until hold timer expires.
(Default 30 minutes)

Calibration Abort- Exit Steps

Exit

ARE YOU SURE?

PRESS ENTER TO

ABORT OR PRESS

LAST SCREEN TO

BACKUP.

SUrE?

Abort calibration vs. Last

Screen option:
The system allows the user

two options when

pressed at any step during the

calibration.
Go to

Exit

Decide whether or not you really want to

exit the calibration process and lose the

new slope and E

Abort

calibration:

Follow step

Exit 3

User enters into the measure mode.
User must refer to

stage 30

for proper air

and fluid flow for measurement mode.
To

Continue

calibration:

is pressed, system will go back to

last screen used in calibration sequence

prior to pressing

Continue to follow calibration according to

Marquee and main display directions.

Exit 3

Press

Exit 4

CALIBRATION

ABORTED
PRESS ENTER

CAL Abrt

Exit 5

Press

Refer to

stage 30

for proper air

and fluid flow for measurement

mode. System return will return

to measure mode.
(Begin again with

stage

retry calibration sequence)

上海肯强贸易有限公司
http://www.kq17.com.cn

Содержание Orion 2111LL























































































































Результаты поиска

Содержание Orion 2111LL

Отзывы:

Похожие инструкции для Orion 2111LL

Бренды по названию

Популярные бренды

Thermo Scientific Orion 2111LL, Руководство пользователя

Результаты поиска

Содержание Orion 2111LL

Отзывы:

Похожие инструкции для Orion 2111LL

Бренды по названию

Популярные бренды