Thermo Scientific KingFisher Flex Скачать руководство пользователя страница 89 | Manualshive

Страница: 89 / 228

background image

Thermo Fisher Scientific

Thermo Scientific KingFisher

®

Flex User Manual

83

Chapter 8

Troubleshooting Guide

Note

Do not use the instrument if it appears that it does not function

properly.

▲

Note that the instrument does not verify the logic flow of the received
commands.

When an error is detected, the current operation is terminated. After an
error, it is best to abort the current run and restart from the beginning
after the problem is fixed. The KingFisher Flex internal software has the
following error messages and warnings (Table 8–8).

Table 8–8.

Error messages reported

Code

Error message

Description

0 No

error

–

1

The command was not recognized as
a valid command

The command was not recognized as a valid KingFisher Flex command.

2

The tip comb holder lifting
mechanism is out of position

The magnetic head position is in error.

3

The turntable rotating mechanism is
out of position

The turntable position is in error.

4

The magnetic head holder lifting
mechanism is out of position

The magnetic tips lift position is in error.

5

The heating block lifting mechanism
is out of position

The heater lift position is in error.

6

The shield plate turning mechanism is
out of position

The shield plate position is in error.

7

Serial number already set

Attempt to set the serial number when it is already set.

8

Invalid command parameter

Invalid command argument.

9

Permanent parameters lost

Nonvolatile parameters lost.

10

Protocol name already used in other
directory

Cannot record a protocol with the same name to another directory.

11

Internal software error

Internal software error. This error is actually never reported because
the firmware halts on detection of an internal error. However, this
error may show up in the error log.

12

The requested movement is not

Cannot perform the requested movement. For example, the head and

Error messages

and warnings

Continued

«
...
87
88
89
90
91
...
»

Содержание KingFisher Flex





































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для KingFisher Flex

Бренд: Rabe Страницы: 65

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Instruments Страницы: 2

Бренд: Hanna Страницы: 12

Бренд: Hanil Страницы: 24

Бренд: Hanil Страницы: 32

Бренд: Hanil Страницы: 24

Бренд: Idmed Страницы: 2

Бренд: NARGESA Страницы: 37

Бренд: NARGESA Страницы: 6

Бренд: Qiagen Страницы: 48

Бренд: Qiagen Страницы: 162

Бренд: Qazqa Страницы: 4

Бренд: Qlightec Страницы: 12

Бренд: Bartscher Страницы: 61

Бренд: Martin Страницы: 202

Aristo WeldCloud Mig U5000i

Бренд: ESAB Страницы: 28

Бренд: Erbe Страницы: 124

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды