Thermo Scientific KingFisher Flex Скачать руководство пользователя страница 73 | Manualshive

Страница: 73 / 228

background image

Thermo Fisher Scientific

Thermo Scientific KingFisher

®

Flex User Manual

67

Chapter 5

Maintenance

For reliable daily operation, keep the instrument free of dust and liquid
spills.

Abrasive cleaning agents are not recommended, because they are likely
to damage the paint finish.

It is recommended that you clean the case of the instrument
periodically to maintain its good appearance. A soft cloth dampened in
a warm, mild detergent solution will be sufficient.

Clean the outside of the instrument and the turntable with clean low-
pressure compressed air or a cloth dampened with water or a mild
detergent when necessary.

Although the KingFisher Flex is constructed from high-quality
materials, you must immediately wipe away spilt saline solutions,
solvents, acids or alkaline solutions from outer surfaces to prevent
damage.

Caution

Painted surfaces can be cleaned with most laboratory

detergents. Dilute the cleaning agent as recommended by the
manufacturer. Do not expose the surfaces to concentrated acids or
concentrated alcohols for prolonged periods of time as damage may
occur.

▲

Clean the display areas with a mild laboratory detergent. The keypad
has a wipe-clean surface.

Plastic covers and surfaces can be cleaned with a mild laboratory
detergent or alcohol.

Warning

If any surfaces are contaminated with biohazardous material,

a mild sterilizing solution should be used.

▲

Caution

Do not autoclave any part of this instrument except the shield

plate.

▲

Keep the turntable surface clean to avoid dust and dirt entering into the
instrument. Clean the turntable surface at least once a week using a soft

Regular and

preventive

maintenance

How to clean the

turntable

«
...
71
72
73
74
75
...
»

Содержание KingFisher Flex





































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для KingFisher Flex

Бренд: Campbell Страницы: 18

Бренд: Vector Страницы: 4

Бренд: Datavideo Страницы: 48

Бренд: Datavideo Страницы: 34

Бренд: Datavideo Страницы: 3

Бренд: Datavideo Страницы: 34

Бренд: Datavideo Страницы: 8

Бренд: Datavideo Страницы: 10

Бренд: Eaton Страницы: 2

Бренд: Eaton Страницы: 20

Бренд: Parker Страницы: 39

Бренд: Gaspardo Страницы: 16

Бренд: HANYOUNG NUX Страницы: 2

Бренд: Halyard Страницы: 88

Бренд: HALDER Страницы: 2

Бренд: Ofa Bamberg Страницы: 80

Бренд: FoodMarble Страницы: 44

Бренд: ISA Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды