Thermo Scientific CarboPac PA200 Скачать руководство пользователя страница 13

Страница: 13 / 37

– Installation

Thermo Scientific

Product Manual for CarboPac PA200 Columns

Page 13 of 37

065734-01

For Research Use Only. Not for use in diagnostic procedures.

On the E-Panel, under Eluent Generator Tab, set the Eluent Polarity to Basic Eluents.

Set KOH

prog

to 100 mM. Turn on the Dionex EGC power.

Condition the Dionex EGC 400 KOH cartridge for 30 min.

On the E-Panel, turn the Dionex EGC power OFF and keep the pump running at 0.1

mL/min for 10 min.

Turn off the pump.

Remove the backpressure tubing from the OUTLET port of the Dionex EGC 400 KOH

cartridge.

Connect the OUTLET port of the Dionex EGC 400 KOH cartridge to the ELUENT IN

port of the Dionex RFIC EGC 400 KOH degasser (Item # 22181-60201).

Connect the ELUENT OUT port of the Dionex RFIC EGC 400 KOH Degasser (Item #

22181-60201) to a PEEK backpressure tubing (Item # 22181-20031). Direct the

backpressure tubing to waste.

With EGC power OFF, turn on the pump at the flow rate of 0.1 mL/min. Flush the Dionex

RFIC EGC 400 KOH Degasser (Item # 22181-60201) for 15 min.

AA.

Turn off the pump.

BB.

Remove the PEEK backpressure tubing (Item # 22181-20031) from the ELUENT OUT

port of the Dionex RFIC EGC 400 KOH Degasser (Item # 22181-60201).

CC.

Connect the ELUENT OUT of the Dionex RFIC EGC 400 KOH Degasser (Item #

22181-60201) to P port of the injection valve.

DD.

Install the column to C port of the injection valve. Direct the OUTLET of the column to

waste.

EE.

With EGC power OFF, turn on the pump and pump DI water at the flow rate of 0.063

mL/min for 15 min.

FF.

With Eluent Polarity set to Basic Eluents, set KMSA

prog

and KOH

prog

to the desired

concentrations for the applications. Turn on the Dionex EGC power for 30 min.

GG.

Connect the OUTLET of the column to the CELL IN of the ED cell, and direct the CELL

OUT to waste.

HH.

Confirm that the pH is >11. With the pH within this range, turn on the cell using the

carbohydrate standard quad waveform. Let the system equilibrate for 30 min.

2.6.2

ICS-6000 Dual EG Start-Up Procedure for CarboPac PA200, 0.4 mm Column

Fill a 2 L eluent reservoir bottle with ASTM filtered, Type I (18-megohm) degassed

deionized water. Connect the reservoir to the eluent inlet line of the pump.

Keep the

water blanketed under an inert gas (helium or nitrogen).

Prime the pump as instructed by the system operation manual.

Remove the vent plug on the top of the Dionex EGC-MSA (Capillary) cartridge (please

refer to Dionex Eluent Generator Cartridges Manual Document No. 065081 for details

about preparation of the Dionex EGC cartridges).

Connect the pump outlet to the EGC IN port of the Dionex EGC-MSA (Capillary)

cartridge and direct the EGC OUT port of the cartridge to waste.

Turn on the pump and pump DI water through the Dionex EGC-MSA (Capillary) for 15

minutes at the flow rate of 0.1 mL/min (prime mode).

Connect the EGC OUT port of the Dionex EGC-MSA (Capillary) cartridge to a PEEK

backpressure tubing (Item # 22181-20032). Direct the backpressure tubing to waste.

Set the pump flow rate to 0.020 mL/min.

Содержание CarboPac PA200






































Результаты поиска

Содержание CarboPac PA200

Отзывы:

Похожие инструкции для CarboPac PA200

Бренды по названию

Популярные бренды

Thermo Scientific CarboPac PA200, Руководство по эксплуатации продукта

Результаты поиска

Содержание CarboPac PA200

Отзывы:

Похожие инструкции для CarboPac PA200

Бренды по названию

Популярные бренды