CSR-20 & CSR-40, September 1999
µ
P-D Controller
Menu Guard Functions
4-31
5.
When all characters in the Container Identification
Number have been entered, press the ENTER key. The
display shows “CID LOAD” and then shows the new
number (left display shows CID11 again as the right dis-
play shows the 11th digit and begins to scroll to the left
again. Check to make sure the Container Identification
Number was entered correctly.
NOTE: If a new controller or new software has
been installed, proceed immediately to “Setting
the Unit Serial Number” below.
Setting the Unit Serial Number
1.
From “CID 11 XXX” (where the scrolling XXX is your
container identification number) in the Guard menu, press
the DOWN key until display shows “USN11 XXX”.
Digits in the right display then begin to scroll to the left as
the last two digits in the left display indicate the position
of the number that is being shown in the right display.
2.
Press the SELECT key to enter the load Unit Serial
Number display. The left display shows “USN11” while
the 11th digit flashes in the right display.
a.
Press the UP or DOWN key to choose a letter (A to
Z), a number (0 to 9) or a blank space.
b.
When the desired character appears in the 11th posi-
tion, press the SELECT key to choose the next posi-
tion. The left display shows “USN10” while the 10th
digit flashes in the right display.
c.
Repeat steps a and b for each character until the Unit
Serial Number is entered.
3.
When all characters in the Unit Serial Number have been
entered, press the ENTER key. The display shows “USN
LOAD” and then shows the new number (left display
shows USN11 again as the right display shows the 11th
digit and begins to scroll to the left again. Check to make
sure Unit Serial Number was entered correctly.
NOTE: If a new controller or new software has
been installed, proceed immediately to “Setting
the Date and Time” below.
Setting the Date and Time
1.
From “USN 11 XXX” (where the scrolling XXX is your
unit serial number) in the Guard menu, press the DOWN
key until the display shows “YEAR 1996”.
a.
Press the SELECT key to enter the load Year display
(left display flashes “YEAR”).
b.
Press the UP or DOWN key to choose the desired
year.
c.
When the desired year shows in the right display,
press the ENTER key. The display shows “YEAR
LOAD” and then shows “YEAR YYYY” (where
“YYYY” is the new year).
2.
If the year is correct, press the DOWN key until the dis-
play shows “MONTH MM” (where “MM” is the
month).
a.
Press the SELECT key to enter the load Month dis-
play (left display flashes “MONTH”).
b.
Press the UP or DOWN key to choose the desired
month.
c.
When the desired month shows in the right display,
press the ENTER key. The display shows “MONTH
LOAD” and then shows “MONTH MM” (where
“MM” is the new month).
3.
If the month is correct, press the DOWN key until the dis-
play shows “DAY DD” (where “DD” is the day).
a.
Press the SELECT key to enter the load Day display
(left display flashes “DAY”).
b.
Press the UP or DOWN key to choose the desired
day.
c.
When the desired day shows in the right display,
press the ENTER key. The display shows “DAY
LOAD” and then shows “DAY DD” (where “DD”
is the new day).
4.
If the day is correct, press the DOWN key until the dis-
play shows “HOUR HH” (where “HH” is the hour).
a.
Press the SELECT key to enter the load Hour display
(left display flashes “HOUR”).
b.
Press the UP or DOWN key to choose the desired
hour.
c.
When the desired hour shows in the right display,
press the ENTER key. The display shows “HOUR
LOAD” and then shows “HOUR HH” (where
“HH” is the new hour).
