Theben thePassa P360-221 DALI UP WH, Руководство пользователя

Страница: 9 / 17

9
Press button A and the button at the same time
for at least 5 s
II
Press the and buttons at the same time for
at least 5 s
III
Scene 1 C1/Scene 2 C1
The required dimming value for lighting channel C1 can be
assigned to scene 1 and scene 2.
Value range (with SendoPro/theSenda B/app)
Adjustable values 0–100%
With the theSenda S or the theSenda B, the lighting is set to a
required brightness and saved as follows:
Press the button for at least 3 s. Scene 1 has been
saved
Press the button for at least 3 s. Scene 2 has been
saved
The scene can be opened by briefly pressing the button.
Control commands via remote control
The following control commands can be triggered with the
remote control:
Control
command
Description Can be
triggered
by Sen-
doPro/
theSenda
B (app)
Can be
trigge-
red by
the-
Senda P
DALI
configuration
Configuration of the operating
mode/DALI components
Change over
to "addressa-
ble" operating
mode
Changeover from "broadcast" to
"addressable". After the changeo-
ver, <thePassa P360-221 DALI>
must be selected as the type.
x
Reset DALI EBs All connected DALI EBs are reset to
the factory setting.
x
Reset DALI
relay
The connected DALI relay is reset to
the factory setting.
x
Switching light The lighting group can be switched
on and off.
x x
Teach-in C1 Activation x x
Presence test OFF/ON x x
Light test OFF/ON x
Restart Restart the detector x x
Factory
settings
Set all parameters and settings to
the factory setting.
x
Changing over to "addressable" operating mode
In factory setting, the detector is in the broadcast operating
mode (<thePassa P360-111 DALI> type). Use the control
command to change over to the <thePassa P360-221 DALI>
detector type which owns 2 addressable lighting groups.
L
After changing over to the addressable mode, the detector
is in the emergency mode. For programming the lighting
groups, see chapter 6 "Start-up".
Teach-in C1
During the teach-in process, the currently measured bright-
ness value is adopted as brightness setpoint value C1. Values
outside the permitted range are automatically set to the
appropriate limit value.
The teach-in control command can be executed with the
SendoPro, the theSenda B/app or with the theSenda P (via
the button).
Factory settings
The presence detector is supplied with the following parame-
ter values: thePassa P360-111 DALI
Parameter Value
Detection zone Z1+Z2
Function C1 Control
Brightness setpoint value C1 200 lux
Room correction factor C1 0.3
Detection sensitivity (PIR) Increment 3
Lighting time delay 5 min
Short-term presence ON
Energy saving mode eco
Presence switch-on delay 0 s
Presence time delay 10 min
Switch on dimming value C1 50%
Configuration type auto
Control speed Standard
Minimum dimming value 10%
Maximum dimming value 100%
Switch off brightness 10 min
Staircase light function OFF
Dimming speed: man. dimming Standard
Response after man. dimming School
Standby time 0 s
Standby dimming value 10%
IR group address C1 I
Scene 1 C1 30%
Scene 2 C1 70%
Configuration button/RC Enabled
LED motion display OFF
L
The parameters can only be reset to the factory setting
with the SendoPro or the theSenda B.
Addressable <thePassa P360-221 DALI>
Setting the teach-in function via button
†
†
Press the button for > 15 s
▻ The currently measured brightness value is adopted as
the brightness setpoint value.
L
The teach-in function via the button can be disabled using
the SendoPro or the theSenda B/app remote controls
when the "Configuration button/RC" parameter is set to
"disabled".