Theben thePassa P360-221 DALI UP WH, Руководство пользователя

Страница: 5 / 17

5
For the DALI configuration, there are 3 options available:
† y
"Group assignment (unaddress.)": only DALI EBs without a
group address are processed.
† y
"Group assignment (all)": all connected DALI EBs are con-
figured. NOTE : All existing group assignments with group
number 1 or 2 are deleted.
† y
"Change group assignment": the next existing EB is
searched for and selected.
▻ After selecting the required group assignment, the
detector is in the programming mode.
▻ A DALI light starts to pulse (random order).
† †
Use to assign the required C1 or C2 channel to the DALI
EB.
† †
For further steps, see "Configuring the lighting groups with
SendoPro".
Configuring the lighting groups using buttons
† †
Set the <Configuration button/RC> parameter to "Enabled".
All connected buttons can be used for the configuration.
† †
Press any button 5 times briefly (< 0.4 s) and press and
hold once (> 15 s).
▻ The LED is switched off.
▻ A DALI light starts to pulse (random order).
▻ The lighting group is assigned by pressing the approp-
riate button:
† y
1 x short button press = channel C1
† y
2 x short button press = channel C2
▻ As confirmation, the light dims to 20% (3 s after the
last button press).
▻ The next DALI light starts to pulse. One after the other,
the lighting groups are assigned to all the lights.
•
If all DALI EBs are assigned to a lighting group, the
detector terminates the configuration process and
restarts (startup phase of 30 s).
▻ The detector switches to the normal operating mode
and the configuration is completed.
L
If required, the configuration process can be ended by
pressing and holding any button for longer than 15 s. The
detector restarts.
▻ In this case, the system is not ready for operation.
L
Instead of using the button, the configuration can also
be carried out with the ON/OFF buttons on the theSenda
B/S.
Checking the configuration
The assignment of the lighting groups can be checked by
switching the individual lighting groups on or off using but-
tons, the SendoPro remote control or the theSenda B/app (for
SendoPro/theSenda B (app), select the "Control commands"
menu).
L
Changing the lighting group for DALI EBs: use the Sendo-
Pro or the theSenda B/app to change the DALI configura -
tion via the "Change group assignment" command.
L
With the button: the whole DALI configuration must be
re-executed.
L
A video on configuring the lighting groups can be found at
https://www.youtube.com/user/TheThebenAG
Switch-on response (configured system)
If voltage is applied, the presence detector goes through two
phases which are indicated by the LED:
1. Start-up phase (30 s)
•
The red LED flashes in one-second intervals; the lighting
is switched on with the switch on dimming value.
•
The detector does not react to button commands or to
the theSenda B/S.
•
If absent, the lighting is switched off after 30 s.
2. Operation
•
The red LED is off. The constant light control or switching
mode are started.
▻ The detector is ready for operation.
7. Functions
 



Z1 Z2
 

Mixed light measurement

Presence detection

Artificial light

Button for manual lighting control

Incident daylight
Lighting channel C1 (broadcast)
Lighting channel C1, C2 (addressable)
The lighting is controlled by presence and brightness. In case
of little daylight and presence, the artificial light is switched
on via the DALI interface and regulated to a constant bright-
ness level.
In case of sufficient daylight or absence, the lighting is swit -
ched off via the DALI interface.
Constant light control
•
It compensates for daylight fluctuations by controlling
the lighting.
•
The total brightness is kept constant at the required
brightness level.
•
The lighting is switched on with the switch on dimming
value and regulated to the set brightness setpoint value.
•
Depending on the "school" or "office" configuration type,
the presence detector responds as follows after manual
dimming using the buttons:
"School" configuration type (in school and conference
rooms):
† y
Manual dimming stops the constant light control.
† y
When someone is present, the lighting remains at the
dimmed value (no brightness influence).
† y
Switching off and on again leads to control mode.