Theben thePassa P360-221 DALI UP WH, Руководство пользователя

Страница: 10 / 17

10
Parameters via remote control
The following parameters can be checked or changed via
the remote control for support during start-up as well as
servicing:
Parameter Description Can be
checked
by Sendo-
Pro/the-
Senda B
(app)
Can be
changed
by Sen-
doPro/
theSenda
B (app)
Can be
changed
by the-
Senda P
Function C1/C2
Selection:
switching/control
x x
Terminal S1
assignment,
terminal S2
assignment
Selection: C1/C2/
C1+C2
x
Brightness
setpoint value
C1, C2
Value range in lux/
measurement off
x x x
Brightness actual
value C1, C2
Check brightness
actual value
x
Room correction
factor C1, C2
Room correction
factor
x x
Brightness mea-
surement value
C1, C2
Lux meter bright-
ness value in lux
x
Detection sensi-
tivity (PIR)
Value range in
increments
x x x
Lighting time
delay
Value range in
seconds/minutes
x x
Short-term
presence
Short-term pre-
sence: ON/OFF
x x
Energy saving
mode
Selection: eco/eco
plus
x x
Presence switch-
on delay
Value range in
seconds/minutes
x
Presence time
delay
Value range in
seconds/minutes
x x
Switch on
dimming value
C1, C2
Value range in % x
Configuration
type C1/C2
Selection: Auto/Man x x x
Control speed
Selection: standard/
average/fast
x
Minimum dim-
ming value
Value range in % x
Maximum dim-
ming value
Value range in % x
Switch off
brightness
Value range in
minutes/hours/
never off
x
Staircase light
function
Selection: ON/OFF x x
Dimming speed:
man. dimming
Selection: standard/
fast
x
Response after
man. dimming
Selection: school/
office
x
Standby time
Value range in
seconds/minutes
Permanently on
x
Standby dim-
ming value
Value range in % x
IR group address
C1, C2
Selection: all/I/II/III
(app to VIII)
x
Scene 1 C1,
scene 2 C1
Scene for lighting
channel C1 value
range in %
x
Scene 1 C2,
scene 2 C2
Scene for lighting
channel C2 value
range in %
x
Configuration
button/RC
Selection: Enabled/
Disabled
x
Parameter Description Can be
checked
by Sendo-
Pro/the-
Senda B
(app)
Can be
changed
by Sen-
doPro/
theSenda
B (app)
Can be
changed
by the-
Senda P
LED motion
display
OFF/ON x
L
The selection of parameters is limited with the theSenda P.
Checking the set values:
With the SendoPro and the theSenda B/app, parameters can
be checked by gradually sending the values to the detector. If
the sent value is below the set parameter, the LED lights up
briefly. If the sent value is equal to or above the set parameter,
the LED lights flickers for 2 s.
Function C1, C2
Lighting channels C1 and C2 can be operated together in
switching mode or in the constant light control function. The
function is set via the <Function C1, C2> parameter.
Value range (with SendoPro/theSenda B/app)
Switching Lighting channels C1 and C2 are in the switching mode
function
Control Lighting channels C1 and C2 are in the constant light control
function
Terminal S1 assignment, terminal S2 assignment
Terminals S1 and S2 for the buttons can be assigned to the
required lighting channel at any time without rewiring.
Value range (with SendoPro/theSenda B/app)
Parameter Lighting channel
Terminal S1
assignment
C1 C2 C1+C2
Terminal S2
assignment
C1 C2 C1+C2
Brightness setpoint value C1, C2
The brightness setpoint value defines the minimum required
brightness. The current brightness is measured below the
presence detector. If the brightness is below the setpoint
value and presence is detected, the light is switched on (for
the fully automatic device configuration type).
A separate brightness setpoint value is available for each
lighting channel C1, C2.
Value range
Adjustable values from SendoPro/theSenda B/app 10–3000 lux
Adjustable values from theSenda P
10, 15, 300,
500, 800 lux
Deactivation of brightness measurement (brightness
measurement has no effect)
The lighting channels only switch according to presence
and absence.
SendoPro/theSenda B/app
Measurement
off
theSenda P
button