TGW CRUZcontrol Скачать руководство пользователя страница 31

Страница: 31 / 62

IOM CRUZcontrol®

P/N: 90480009

Revision Date: 03/18/2019

Page

Zone Status Indication

Definition:

Indicates full or empty status of the downstream zone.

Action:

Takes an input from one of two user selectable inputs and outputs to the Zone Status

Output on TB5.

Configuration: Choose the input that determines the zone’s empty or full status:



Downstream logic signal (identical to Downstream Sensor signal of a Single

Accumulation Logic Assembly) as the input: JP4 is on 1-2 or 2-3



Auxiliary sensor or external signal (from a PLC for example) as the input:

JP4 is NC and signal is input to TB4

Release Function Module

Technical Data

Interface to CRUZcontrol

ZLM1, WLR2100-D

Upstream connection

Female, M12, 4-PIN, 300 mm cable

Downstream connection

Male, M12, 4-PIN, 300 mm cable

Power

Supply voltage from daisy chain

18…30 VDC

Power consumption of ZIM

10 mA, no load

ZoneControl system power TB4 input

24…28 VDC typical. Limit values: 18…30 VDC

Input ratings

TB4 Power VDC, Common

24 VDC typical, 30 VDC max.

TB4 Release/Interrupt input

18…30 VDC

Guaranteed OFF Voltage: <= 4.0 VDC

Guaranteed ON Voltage: >= 15.0 VDC

Typical ON state current draw @24V: 4mA

TB1 Single Release/Logic Interrupt

18…250 UC

Guaranteed OFF Voltage: <= 4 UC

Guaranteed ON Voltage: >= 15.0 UC

Typical ON state current draw 2.5 mA

TB2 Slug Release input

18…250 UC

Guaranteed OFF Voltage: <= 4 UC

Guaranteed ON Voltage: >= 15.0 UC

Typical ON state current draw 2.5 mA

Output ratings

TB5 Logic output

PNP; 2.21 kohm impedance typical

TB5 Zone Status output

PNP; 2.21 kohm impedance typical

Physical properties

Terminal block

Terminal block wire

30 to 12 AWG (2.5 … 0.2mm², strip length ¼" (6.0 mm)

Screw terminal torque

5 in-lbs. (0.56 Nm)

Housing

Dimensions

5.125" x 3.75" x 1.125" (130mm x 95mm x 29mm)

Mounting

3/16" holes in mounting flange or double sided adhesive, any orientation

Enclosure rating

IP 42, NEMA 1

Sock and vibration

IEC 68 2-27, IEC 68 2-29, and EC 68 2-6

Operating temperature

-13…131°F (-25…55°C)

Storage temperature

-40…185°F (-40…85°C)

Approximate weight

0.9 lb. (400 g)

1. These inputs are optically isolated from the rest of the Class 2 circuitry. Isolation voltage from Universal-Voltage

inputs to Class 2 circuitry: 5000Vrms. Inputs are not sensitive to polarity.

2. Optically isolated solid state relay with 1 Normally Open and 1 Normally Closed contact. Isolation voltage from

ZONE STATUS relay terminals to Class 2 circuitry: 5000Vrms

Содержание CRUZcontrol































































Результаты поиска

Содержание CRUZcontrol

Отзывы:

Похожие инструкции для CRUZcontrol

Бренды по названию

Популярные бренды

TGW CRUZcontrol, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание CRUZcontrol

Отзывы:

Похожие инструкции для CRUZcontrol

Бренды по названию

Популярные бренды