TGW CRUZcontrol Скачать руководство пользователя страница 29

Страница: 29 / 62

IOM CRUZcontrol®

P/N: 90480009

Revision Date: 03/18/2019

Page

Full Function Module

(Note: “ZIM” as found in this table refers to Function Module)

Downstream

LOGIC

Downstream

SLUG

JP1

JP2

Upstream

SLUG

TB5 (pin

Note

1-2

No Slug signal

1-2

Downstream Slug pass-through, Upstream Slug pass-through

1-2

2-3

Downstream Slug pass-through, Upstream Slug interrupt

2-3

Downstream Slug interrupt

4-5

Logic Crossover

4-5

1-2

Logic Crossover, Upstream Slug pass-through

4-5

2-3

Logic Crossover, Upstream Slug interrupt

Upstream

SLUG

JP2

JP1

Downstream

SLUG

TB5 (pin 4)

1-2

No Slug signal

1-2

Upstream Slug pass-through, Downstream Slug pass-through

1-2

2-3

Upstream Slug pass-through, Downstream Slug interrupt

1-2

4-5

Upstream Slug pass-through, Downstream Logic Crossover

2-3

Upstream Slug interrupt

INPUTS

TB5 (pin 4)

JP1

Downstream

SLUG

JP2

Upstream

SLUG

1-2

Downstream Slug pass-through, Upstream Slug pass-through

2-3

Downstream Slug interrupt, Upstream Slug interrupt

4-5

1-2

Downstream Logic crossover, Upstream Slug pass-through

INPUTS

TB2

JP1

Downstream

SLUG

JP2

Upstream

SLUG

TB5 (pin

Note

1-2

Downstream Slug pass-through, Upstream Slug pass-through

2-3

Downstream Slug interrupt, Upstream Slug interrupt

4-5

1-2

Downstream Logic crossover, Upstream Slug pass-through

STATE

Typical System Definition

Downstream zone is FULL

Downstream zone is EMPTY

SLUG

line not active.

SLUG

line active

1-2

Downstream Slug pass-through. Downstream cable

SLUG

line connected directly to ZIM circuitry

2-3

Downstream Slug interrupt. Downstream cable

SLUG

line isolated from ZIM circuitry

Logic Crossover. Downstream

LOGIC

signal activates ZIM SLUG driver circuitry.

Downstream cable

SLUG

line isolated from ZIM circuitry.

SLUG

line not active

SLUG

line active

1-2

Upstream Slug pass-through. Upstream cable

SLUG

line connected directly to ZIM circuitry

2-3

Upstream Slug interrupt. Upstream cable

SLUG

line isolated from ZIM circuitry

SLUG

line not active

SLUG

line active

No effect

Slug Release (activate ZIM

SLUG

driver circuitry)

Truth Table for Slug Circuitry (Upstream Inputs)

OUTPUTS

Truth Table for Slug Circuitry (Downstream Inputs)

Truth Table Definitions

OUTPUTS

Electrical Definition

Downstream

LOGIC

<4.0VDC

>15VDC

---

Upstream

SLUG

TB5 (pin 4)

---

JP2

<4.0VDC

>15VDC

---

INPUTS

---

JP1

INPUTS

OUTPUTS

Note

OUTPUTS

Downstream

SLUG

Truth Table for Slug Circuitry (TB5, pin 4 Input)

Truth Table for Slug Circuitry (TB2 Input)

<4.0VDC

>15VDC

TB2

<4VAC/DC

>15VAC/DC

<4.0VDC

>15VDC

---

4-5

Содержание CRUZcontrol































































Результаты поиска

Содержание CRUZcontrol

Отзывы:

Похожие инструкции для CRUZcontrol

Бренды по названию

Популярные бренды

TGW CRUZcontrol, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание CRUZcontrol

Отзывы:

Похожие инструкции для CRUZcontrol

Бренды по названию

Популярные бренды