Textron Stampede 900 2017, Руководство по ремонту и обслуживанию

Страница: 50 / 237

B
38
Repair and Service Manual
ROLLOVER PROTECTION SYSTEM
Read all of SAFETY and this section before attempting any procedure. Pay particular attention to Notices, Cautions, Warnings and Dangers.
668061
The ROPS hardware and compo-
nents must be assembled properly
and all hardware tightened to the
torques specified for the ROPS to provide occupant
protection during a rollover.
Do not drill holes in the ROPS components or mod-
ify the ROPS in any way.
Removing the ROPS as a Complete Unit
Tool List Qty.
Socket, 15mm..............................................................1
Ratchet ........................................................................ 1
Wrench, 15mm ............................................................1
Torque Wrench, ft. lbs..................................................1
1.
Disconnect CHMSL (Center High Mounted Stop
Light) wire connection at the bottom of the passen-
gers side C-pillar.
2. Remove the bolts (8) and the nuts (9) that secure the
ROPS side tubes (1 and 2) to the seat back supports
(24) (Ref. Fig. 1).
3. Remove the bolts (8) and the mounting plate (10)
that secure the front of the ROPS side tubes (1 and
2) to the A-pillar of the frame.
4. Remove the bolts (8) and the mounting plate (11)
that secure the rear of the ROPS side tubes (1 and
2) to the B-pillar of the frame.
5. Remove the bolts (8) and the mounting plate (11)
that secure the extended cab tubes (4 and 6) to the
C-pillar of the frame.
6. With the aid of an assistant, lift the ROPS off the
vehicle.
7. Installation is the reverse order of removal.
NOTICE: Loosen all ROPS hardware before installa-
tion to allow the mounting holes to align properly.
8. Tighten hardware to the torque specified below:
INSTALLING ROPS COMPONENTS
NOTICE: Loosen all ROPS hardware before installa-
tion to allow the mounting holes to align properly.
A. ROPS Side Tube Installation
Tool List Qty.
Socket, 15mm..............................................................1
Ratchet ........................................................................ 1
Wrench, 15mm ............................................................1
1. Remove the cargo tray and cab closeout panel. See
the BODY section.
2. Position the driver side ROPS tube (1) as shown
(Ref. Fig. 1). Secure the front of the side ROPS tube
(1) to the vehicle frame A-pillar with bolts (8) and
mounting plate (10). Finger tighten hardware to allow
for adjustment.
3. Attach the other end of the driver side ROPS tube (1)
to the B-pillar. Secure with bolts (8) and mounting
bracket (11). Finger tighten hardware to allow for
adjustment.
4. Repeat the above steps for installing the passenger
side ROPS tube (2).
B. ROPS Extended Cab Tubes Installation
Tool List Qty.
Socket, 15mm ..............................................................1
Ratchet.........................................................................1
Wrench, 15mm.............................................................1
Fig. 2
1. Position the lower end of the extended cab ROPS
tube (4) over the driver side C-pillar of the vehicle
frame and secure with bolts (8) and nuts (9) (Ref.
Fig. 1). Finger tighten hardware to allow for adjust-
ment.
2. Repeat the above steps for installing the passenger
side extended cab ROPS tube (6).
3. Do not install the top bracket hardware of the
extended cab ROPS tube (4 and 6) until the rear
cross-tube (12) has been installed (Ref. Fig. 2).
C. Rear Cross-tube Installation
Tool List Qty.
Socket, 15mm ..............................................................1
Ratchet.........................................................................1
Wrench, 15mm.............................................................1
ITEM NO TORQUE SPECIFICATION
8
37 - 41
ft.lbs. (50 - 55 Nm)
Front of Vehicle
9
9
8
12
4
7