manualshive.com logo in svg

Texas Instruments TMS470R1x, Справочное руководство

Поделиться
Скачать
Texas Instruments TMS470R1x Скачать руководство пользователя страница 18

MibSPI Operation Modes

10

SPIENA pin will allow the master SPI to drive the clock pulse stream;
otherwise, the master will hold the clock signal. 

To use the SPIENA as a WAIT signal pin, the slave SPIENA pin must be
configured as functional (SPIPC6.0 = 1). If the SPIENA pin is in high-z mode
(ENABLE_HIGHZ = 1), the slave will put SPIENA into the high-impedance
once it receives a new character. If the SPIENA pin is in push-pull mode
(ENABLE_HIGHZ = 0), the slave will drive SPIENA high once it receives a
new character. The slave will drive SPIENA low again after new data is written
to the slave shift register (SPIDAT0).

Figure  4.

MibSPI Four-Pin Option with SPIENA

2.4

MibSPI Operation; Five-Pin Option (Hardware Handshaking)

To use the hardware handshaking mechanism, both the SPIENA pin and
SPISCS [7:0] pin must be configured as functional pins. 

Compatibility mode

In the master SPI (CLKMOD = 1), the SPIENA pin is configured as a
functional input. If configured as a slave SPI, the SPIENA pin is configured as
a functional output. If the SPIENA pin is in high-z mode (ENABLE_HIGHZ =
1), the slave SPI will put this signal into the high-impedance state if it receives
a new character from the master or if the slave becomes de-selected by the
master (SPISCS goes high). The slave will drive the signal SPIENA low when

MibSPI four pin option (2)

Master

Slave

(Master = 1 ; CLKMOD = 1)

(Master = 0 ; CLKMOD = 0)

SPIDAT0

SPIDAT0

MSB

LSB

MSB

LSB

Write to 

SPIDAT0

SPISOMI

SPISIMO

SPISOMI

SPISIMO

SPICLK

SPICLK

SPIENA

SPIENA

Write to 

Write to SPIDAT0 (SLAVE)

Write to SPIDAT0 (Master)

SPICLK

SPISIMO

SPISOMI

SPIENA

Содержание TMS470R1x














































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды