background image

25

    It is the fourth of the 8 different setting parameters in the advanced settings menu. To change 

the Operating Voltage Settings, press the SET button while the Operating Voltage page is on the 

screen.
    In this page, you can navigate between the parameters (Control mode, High Voltage, Low 

Voltage and Delay) with the RIGHT button and change the value in the selected parameter with 

the UP / DOWN buttons.
     To change the current value, the relevant parameter must be selected with the RIGHT button. 

The selected parameter is indicated by the "

>

" sign on the left side.

    In this page, voltage control mode can be activated or deactivated, high voltage and low 

voltage value can be set. If the voltage rises above the set high voltage set value while the 

voltage control mode is active or falls below the low voltage set value, the device waits for the 

set delay time and then stops compensation. Then “High Voltage” or “Low Voltage” warning is 

displayed on the screen. Also, "ALR" contact is activated. When the voltage control mode is 

passive, the device does not control the voltage.

Settings

 

E

Advanced Settings Menu 

E

Operating Voltage

OPERATING VOLTAGE

Menu.3.4

Operating Voltage

 High   V.:  260 V
 Low    V.:  150 V
 Delay    :  5sec

>Control  :  Active

Menu.3.4.1

Voltage(V)  Curr.(A)

L1:220.0    L1:380.0
L2:220.0    L2:380.0
L3:220.0    L3:380.0

_____________________
ALR! Low Voltage

    It is the fifth of the 8 different setting parameters in the advanced settings menu. To change 

the Operating Harmonics Settings, press the SET button while the Operating Harmonics page is 

on the screen.
    In this page, you can navigate between parameters (Control mode, Voltage Harmonic Set 

Value, Current Harmonic Set Value and Delay) with the RIGHT button and change the value of 

the selected parameter with the UP / DOWN buttons.
     To change the current value, the relevant parameter must be selected with the RIGHT button. 

The selected parameter is indicated by the "

>

" sign on the left side.

    In this page, voltage control mode can be activated or deactivated, voltage harmonic and 

current harmonic value can be set. If harmonics exceed the set values   while harmonic control 

mode is active, the device waits for the set delay time, then stops compensation. Then “High 

THDI” or “High THDV” warning is displayed on the screen. Also, "ALR" contact is activated. 

When the harmonic control mode is passive, the device does not control the harmonics.

Settings

 

E

Advanced Settings Menu 

E

Operating Harmonic

Operating Harmonic

 THDV     :  5  %
 THDI     :  50 %
 Delay    :  30sec

>Control  :  Active

Menu.3.5.1

Voltage(V)  Curr.(A)

L1:220.0    L1:380.0
L2:220.0    L2:380.0
L3:220.0    L3:380.0

_____________________
ALR!  High THDI

OPERATING HARMONIC

Menu.3.5

26

    It is the sixth of the 8 different setting parameters in the advanced settings menu. To enter 

the Delete Records menu, press the SET button while the Delete Records page is on the screen.
    In this page, you can navigate between the parameters (Energy Value, Power Analysis and 

Ratios) with the RIGHT button, and change the value of the selected parameter with (UP / 

DOWN) buttons.
     To change the current value, the relevant parameter must be selected with the RIGHT button. 

The selected parameter is indicated by the "

>

" sign on the left side.

    

Example: 

To delete the ratios, after entering the menu, we select the “Ratios” parameter by 

pressing the RIGHT button 2 times. Then we change the “Undel” option to “Del” by pressing the 

UP or DOWN button. Finally, when we press the SET button, all parameters marked as “Del” 

are deleted. If you exit the menu with ESC button without pressing the SET button, the selected 

parameters will not be deleted.

Settings

 

E

Advanced Settings Menu 

E

Delete Logs

DELETE LOGS

Menu.3.6

Delete Logs

>Energy Value : Undel

           Del/Undel

 Power Analys.: Undel
 Ratios       : Undel

Menu.3.6.1

    It is the seventh of the 8 different setting parameters in the advanced settings menu. To 

change the Generator Compensation Settings, press the SET button while the Generator 

Compensation page is on the screen.
    In this page, you can navigate between the parameters (Control, Set and Tolerance) with the 

RIGHT button and change the value in the selected parameter with the UP / DOWN buttons.
     To change the current value, the relevant parameter must be selected with the RIGHT button. 

The selected parameter is indicated by the "

>

" sign on the left side.

    In this page, generator control mode can be activated or passive, generator compensation set 

and tolerance value can be entered. When the generator mode is activated, it compensates 

according to the set and tolerance value set while the generator is activated. When the 

generator mode is passive, compensation is stopped when the generator is activated.
    

NOTE:

 In order to use this feature, phase-neutral connection should be made to the 

Generator connection terminal of the device so as to energize this terminal when the generator 

is running.
    

NOTE:

 While the generator in the system is activated, the word “GEN” will appear on the 

device's screen (bottom left of the screen) as in the figure above.

Settings

 

E

Advanced Settings Menu 

E

Generator Settings

GENERATOR

SETTINGS

Menu.3.7

>Control  :  Active
 Set      :  5%

 Cos:0.9983  Induct.

   Tolerance: 

   

%4.0

Generator Settings

Menu.3.7.1

Kosinus(Cos)

L1: -0.945
L2:  0.145
L3: -0.458

_____________________

TCR

 

%

  

R:00 S:00 T:00

Offset

0.0

Cosinus(Cos)

L1: -0.945
L2:  0.145
L3: -0.458

_____________________

GEN

 

%

  

R:00 S:00 T:00

Offset

0.0

Содержание RGT-12SVC







































Отзывы: