background image

15

How to Enter the Step Value Manually?

    When you enter the Step Menu page, the Step Values   page 

is displayed on the screen first.
    Switch to the Manual Step Value Set page by pressing the 

UP button, then enter the Manual Step Value Set page by 

pressing the SET button.

     In this page, you can navigate between parameters (Step, 

Type and Value) with the RIGHT button, and change the value 

in the selected parameter with the UP/DOWN buttons.
    To change the current value, the relevant parameter must 

be selected with the RIGHT button. The selected parameter is 

indicated by the sign "

>

" on the left side.

MANUAL STEP

VALUE SET

Menu.2.6

Enter Step Value

 Type   : L123
 Value  : -10.00kvar

>Step   : 1

Menu.2.6.1

     After entering the step information manually, SET button is 

pressed to save. After the saving process, the step 

information recorded and “Step Approved” are displayed on 

the screen. 

    

    To exit without saving, pressing the ESC button will return 

to the Maneul Step Value Set page.

Enter Step Value

 Type   : L123
 Value  : -10.00kvar

>Step   : 1

Menu.2.6.1

Step Approved

    Example:

 On the screen above, the three-phase 10kVAr capacitor value has been entered in the 1st step.

    

    If the value to be entered is single phase, “L1, L2 or L3” should be selected from the phase part 

according to the phase to which it is connected. If the value to be entered is two phase, “L12, L23 or L31” 

should be selected from the phase part according to the phase to which it is connected. If the value to be 

entered is three phase, “L123” should be selected.

    Note:

 Capacitor values a  re entered as (-) signed with DOWN button. Shunt reactor values a  re entered 

unsigned with the UP button.

    When SET button is pressed on any measurement page, the 

PASSWORD page is displayed for entering the menu.

    While on this page, press the SET button to enter the menu.

    (The password value is “0000” by default. If the password 

has been changed by the user, the password determined by 

the user must be used to enter the menu.)

    After passing the password page, Current Transformer 

Menu page will be displayed on the screen.
     While on this page, press UP button to switch to the Step 

Menu page.
    The Step Menu page will appear on the screen. Press the 

SET button to enter the Step Menu page.

STEP MENU

Menu.2.0

Enter Password!
PASS : 0000

16

How is Step Control Done?

    It is a menu designed to control the connections and 

robustness of the shunt reactors, capacitors and contactors 

connected to the stages.
        When SET button is pressed on any measurement page, 

the PASSWORD page is displayed for entering the menu.

    While on this page, press the SET button to enter the menu.

    (The password value is “0000” by default. If the password 

has been changed by the user, the password determined by 

the user must be used to enter the menu.)

    After passing the password page, Current Transformer 

Menu page will be displayed on the screen.
     While on this page, press UP button to switch to the Step 

Menu page.
    The Step Menu page will appear on the screen. Press the 

SET button to enter the Step Menu page.

    When you enter the Step Menu page, the Step Values   page 

is displayed on the screen first.
    Switch to the Step Control page by pressing the UP button, 

then enter the Step Control page by pressing the SET button.

    In this page, you can navigate between the steps with UP / 

DOWN buttons, you can use the RIGHT button to control / 

activate the steps and passive the active steps.

    

    Active steps are indicated by the "*" sign.
    When you return to the measurements screen by pressing 

the ESC button, if there are any steps you have activated 

manually, the device will make these steps passive one by one.

Measurement Screen Introduction

Measurements

 

E

L1:220.0    L1:380.0
L2:220.0    L2:380.0
L3:220.0    L3:380.0

_____________________
TCR

 

%

  

R:23 S:23 T:23

Voltage(V)   Curr.(A)

1

2

3

1- The area where the name and unit 

of the measured value are specified.
2- The area where the measured values   

are displayed.

3- The area where the SVC (TCR) usage 

percentage and Alarm states are displayed.
NOTE.:

 While the generator in the system is 

activated, “GEN” * will appear on the screen 

instead of “TCR”. (*: It is valid when the 

generator is connected to the device.)

    While on any measurement screen, you can switch to other measurement screens by using 

UP / DOWN or RIGHT buttons.

STEP CONTROL

Menu.2.5

>01[*]  05[ ]  09[ ]

02[ ]  06[ ]  10[ ]
03[ ]  07[ ]  11[ ]

TCR[ ]     

 

04[ ]  08[ ]  12[ ]

Menu.2.5.1   Control

STEP MENU

Menu.2.0

Enter Password!
PASS : 0000

Содержание RGT-12SVC







































Отзывы: