Tennant Litter Hawk Скачать руководство пользователя страница 67

Страница: 67 / 88

MAINTENANCE

Litter Hawk

330470 (12--99)

BRUSHES

SIDE BRUSHES

The side brushes sweep debris from the outer

edges of the machine into the path of the main

vacuum head.

Check the brushes daily for wear or damage.

Remove any string or wire found tangled on the

side brushes or side brush drive hubs.

Check the side brush pattern daily. The side brush

bristles should contact the floor in an 8 o’clock to

4 o’clock pattern when the brush is in motion.

Adjust the side to side position of the brushes

with the side brush bracket weldments in the front

of the side brush arms. A spacer can be added to

the top bolt of the right side mounting bracket, and

lower bolt on the left side mounting bracket, to

help give the brushes proper tilt.

Adjust the vertical tension of the brushes with the

tension spring bolt eyes. Turn the bolt eyes

counterclockwise to increase the brush contact

with the sweeping surface, and clockwise to

decrease the brush contact with the sweeping

surface.

Содержание Litter Hawk

























































































Результаты поиска

Содержание Litter Hawk

Отзывы:

Похожие инструкции для Litter Hawk

Бренды по названию

Популярные бренды

Tennant Litter Hawk, Руководство оператора

Результаты поиска

Содержание Litter Hawk

Отзывы:

Похожие инструкции для Litter Hawk

Бренды по названию

Популярные бренды