Tennant Litter Hawk Скачать руководство пользователя страница 12

Страница: 12 / 88

OPERATION

Litter Hawk

330470 (12--99)

IGNITION SWITCH

The

ignition switch

controls machine power with a

key.

FOR SAFETY: When starting machine,

keep foot on brake and directional lever

in neutral.

Preheat: Turn and hold the key counterclockwise.

The glow plug light will come on. When the glow

plug light goes out, usually in 5 to 30 seconds

depending on weather conditions, the engine is

ready to start.

Start: Turn the key all the way clockwise, and

release the key as soon as the engine starts.

Stop: Turn the key counterclockwise.

Accessory power: Turn the key clockwise to the

next position from the off position.

STEERING HANDLE

The

steering handle

controls the machine’s

direction. The machine is very responsive to the

steering wheel movements.

Left: Turn the steering handle to the left.

Right: Turn the steering handle to the right.

FUEL LEVEL GAUGE

The

fuel level gauge

indicates how much fuel is in

the fuel tank.

NOTE: Do not allow the fuel tank to empty

completely. Air can enter the fuel system, and it

may need bleeding before the next engine start.

Содержание Litter Hawk

























































































Результаты поиска

Содержание Litter Hawk

Отзывы:

Похожие инструкции для Litter Hawk

Бренды по названию

Популярные бренды

Tennant Litter Hawk, Руководство оператора

Результаты поиска

Содержание Litter Hawk

Отзывы:

Похожие инструкции для Litter Hawk

Бренды по названию

Популярные бренды