Tennant Litter Hawk Скачать руководство пользователя страница 27

Страница: 27 / 88

OPERATION

Litter Hawk

330470 (12--99)

POSITIONING STEERING ASSEMBLY

The Litter Hawk

may be operated from two

different positions. The operator may sit on the

machine and steer from the front, or walk behind

the machine and steer from the rear.

To move the steering assembly from the front or

the rear of the machine:

1. Turn ignition key counterclockwise to stop

the engine. Apply the machine parking

brake.

2. Turn steering assembly knob

counterclockwise until the steering assembly

may be lifted off the front notched steering

plate.

NOTE: The machine will not operate unless the

steering assembly is held securely in place with

the steering assembly knob.

3. Raise the rear notched steering plate cover,

and fold it over onto the seat.

4. Lift the steering assembly off the front

notched steering plate. Unfold the steering

assembly back over the machine seat.

Содержание Litter Hawk

























































































Результаты поиска

Содержание Litter Hawk

Отзывы:

Похожие инструкции для Litter Hawk

Бренды по названию

Популярные бренды

Tennant Litter Hawk, Руководство оператора

Результаты поиска

Содержание Litter Hawk

Отзывы:

Похожие инструкции для Litter Hawk

Бренды по названию

Популярные бренды