Tennant Litter Hawk Скачать руководство пользователя страница 33

Страница: 33 / 88

OPERATION

Litter Hawk

330470 (6--99)

CLEANING AND BRUSH INFORMATION

Pick up oversized debris before cleaning. Pick up

pieces of wire, twine, string, etc., which could

become entangled in the brushes. There is only

one set of side brushes recommended for use

with the Litter Hawk

Polypropylene side brush

-- A good general

purpose brush for sweeping light to medium

debris in outdoor applications. This brush is

recommended for dry or wet conditions.

Plan the cleaning in advance. Try to arrange long

runs with minimum stopping and starting. Drive

the straightest path possible. Avoid bumping into

posts or scraping the sides of the machine.

When operating the machine, turn the steering

handle with a smooth, even motion. Avoid sudden

turns, except in emergencies.

The dust control system is useful in dry conditions

to control the dust stirred up by the side brushes

and vacuum fan. The system consists of a water

pump switch, water tank, two water pumps and

three spray nozzles.

Содержание Litter Hawk

























































































Результаты поиска

Содержание Litter Hawk

Отзывы:

Похожие инструкции для Litter Hawk

Бренды по названию

Популярные бренды

Tennant Litter Hawk, Руководство оператора

Результаты поиска

Содержание Litter Hawk

Отзывы:

Похожие инструкции для Litter Hawk

Бренды по названию

Популярные бренды