Tennant Litter Hawk Скачать руководство пользователя страница 58

Страница: 58 / 88

MAINTENANCE

Litter Hawk

330470 (12--99)

LUBRICATION

ENGINE

Check the engine oil level daily. Change the

engine oil and oil filter after every 100 hours of

operation. Use engine oil with a diesel rating

above

CD grade.

Fill the engine with oil to the level indicated on the

oil dipstick. Low oil level is indicated by the mark

closest to the end of the dipstick. Full level is

indicated by the mark closest to the top of the

dipstick. The engine oil capacity is 3.25 L (3.4 qt)

without the oil filter.

The engine oil drain plug is located underneath

the machine on the bottom of the oil pan.

The engine oil filter is mounted on the right side of

the machine, under the engine alternator.

WARNING: Moving fan blades. Keep

away.

REAR WHEEL SUPPORT BEARINGS

The rear wheel support bearings have two grease

fittings on the collar between the bearings. They

are located at the base of the rear wheel support

shaft, in front of the radiator.

Lubricate with Lubriplate EMB grease (Tennant

part number 01433--1) after every 400 hours of

machine operation.

Содержание Litter Hawk

























































































Результаты поиска

Содержание Litter Hawk

Отзывы:

Похожие инструкции для Litter Hawk

Бренды по названию

Популярные бренды

Tennant Litter Hawk, Руководство оператора

Результаты поиска

Содержание Litter Hawk

Отзывы:

Похожие инструкции для Litter Hawk

Бренды по названию

Популярные бренды