Tennant Litter Hawk Скачать руководство пользователя страница 18

Страница: 18 / 88

OPERATION

Litter Hawk

330470 (2--05)

CHARGING SYSTEM LIGHT

The

charging system light

comes on when the

alternator is not operating within normal range;

13.5 to 15.5V. If the light comes on, stop

operating the machine. Locate the problem, and

have it corrected.

THERMO SENTRY LIGHT

The

Thermo Sentry light

comes on when the

Thermo Sentry senses excessive heat in the

hopper, possibly from a fire. The Thermo Sentry

will also shut off the vacuum fan. If this happens,

stop the machine and eliminate the source of

heat. Allow the sensor to cool, and it will reset

automatically.

HAZARD LIGHT SWITCH (001580--

)

The

hazard light switch

controls the hazard lights.

On: Press the center of the hazard light switch.

Off: Press the center of the hazard light switch

again.

Содержание Litter Hawk

























































































Результаты поиска

Содержание Litter Hawk

Отзывы:

Похожие инструкции для Litter Hawk

Бренды по названию

Популярные бренды

Tennant Litter Hawk, Руководство оператора

Результаты поиска

Содержание Litter Hawk

Отзывы:

Похожие инструкции для Litter Hawk

Бренды по названию

Популярные бренды