Tennant Litter Hawk Скачать руководство пользователя страница 15

Страница: 15 / 88

OPERATION

Litter Hawk

330470 (6--99)

VOICE BOX SWITCH (OPTION)

The

voice box switch

controls the pre--recorded

voice message. See the VOICE BOX section of

this manual.

Replaying message on : Press and release the

top of the voice box switch.

Message off: Press the bottom of the voice box

switch.

VACUUM FAN/SIDE BRUSHES SWITCH

The

vacuum fan/side brushes switch

controls the

vacuum fan and side brushes.

Vacuum fan on: Press the top of the vacuum

fan/side brush switch. The vacuum fan will turn

on. The side brushes will also turn on, but will

remain in the raised position.

Vacuum fan on/side brushes down and on: Press

the bottom of the vacuum fan/side brushes

switch. The vacuum fan will turn on. The side

brushes will also turn on and lower to the cleaning

position.

Vacuum fan off/side brushes up and off: Press the

switch to the middle off position. The vacuum fan

will turn off. The side brushes will also turn off,

and will raise to the off position.

Note: Excessive heat in the hopper will cause the

Thermo Sentry

to shut off the vacuum fan.

If this happens, stop the machine, eliminate the

source of heat. Turn the switch to the off position

and back on to reset.

Содержание Litter Hawk

























































































Результаты поиска

Содержание Litter Hawk

Отзывы:

Похожие инструкции для Litter Hawk

Бренды по названию

Популярные бренды

Tennant Litter Hawk, Руководство оператора

Результаты поиска

Содержание Litter Hawk

Отзывы:

Похожие инструкции для Litter Hawk

Бренды по названию

Популярные бренды