Teltonika FM1100 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 82

Teltonika FM1100 Скачать руководство пользователя страница 22

22

SMS. GPRS mode is the most preferred data sending mode. SMS mode is mostly used in areas
without GPRS coverage or GPRS usage is too expensive.

GPRS and SMS settings are described in later sections. FM1100 communicates with server

using special data protocol. Data protocol is described in “FMXXXX Protocols” document.

FM1100 can be managed by SMS commands. SMS Command list is described in SMS

COMMAND LIST section

.

Module configuration can be performed over TCP or via SMS.

Configuration parameters and modes are described in “FMXXXX Protocols” document.

5.2

Sleep modes

5.2.1

Sleep mode

FM1100 is able to go to Sleep mode after configurable Sleep timeout. This timeout

(defined period) starts counting when device is in STOP mode. After timeout is reached and all
conditions for sleep mode are met, device goes to sleep mode

.

While in sleep mode, FM1100

turns GPS module off and it is not making new periodic records. Only event records is being
recorded with last known coordinate and sent to AVL server. As a result power usage decreases
allowing saving vehicle battery.

FM1100 can enter sleep mode if

ALL

of these conditions are met:



FM1100 has to be configured to work in Sleep mode and Sleep timeout is reached;



Device must be synchronized time with GPS satellites;



No movement by movement sensor is detected;



Ignition (DIN1) is off;

FM1100 exits sleep mode when if

ONE

of following conditions are true:



Movement by movement sensor is detected;



Ignition (DIN1) is turned on;

5.2.2

Deep Sleep mode

While in deep sleep mode, FM1100 sets GPS receiver to sleep mode and turns off

GSM/GPRS  module  (it  is  not  possible  to  wake  up  device  via  SMS).  Despite  records  with  last
known  coordinate  are being  saved  and  send to AVL  server  (GSM/GPRS module  is turned  on to
send  data  and  after  that  it  is  turned  off  again),  power  usage  is  decreased  to  save  vehicle’s
battery. Note, that power saving depends on two configurable parameters: send period and min.
record saving period.

FM1100 can enter deep sleep mode if

ALL

of these conditions are met:



FM1100 has to be configured to work in Deep Sleep mode and Sleep timeout set;



Device must be synchronized time with GPS satellites;



No movement by movement sensor is detected;



Ignition (DIN1) is off;



Min. Record Saving Period (Data Acquisition Mode settings) must be bigger than
Active Data Link Timeout parameter, that FM1100 could close GPRS link.



Send period (Data Acquisition Mode settings) minus Active Data Link Timeout must
be more than 90 sec., that FM1100 could close GPRS link for at least 90 sec.



USB cable is not connected.

«
...
20
21
22
23
24
...
»

Содержание FM1100



















































































Отзывы:

Нет отзывов