background image

 

10

2.5.4  Phone number settings 

 

1 - 4. Phone number

: 4 user telephone numbers can be entered where alarms will be 

reported through voice call and/or SMS message (according to event settings). 

 

Acknowledgement

: three confirmation modes can be selected: 

o

 

0 - no ack.

:

 

event confirmation is not necessary 

o

 

1 - * = ack.

: event must be confirmed by pressing * key on the phone 

o

 

2 - * = ack, # = stop

: event must be confirmed by pressing 

*

 key on the phone, 

or the reporting of the given event to further phone numbers can be cancelled by 
pressing 

#

 key on the phone. 

(Reporting of all pending events waiting to be reported can be canceled by 
entering *

module password

# on the phone e.g. *1111# for default passw.). 

 

 

Caller ID

: there are seven modes of caller identification for incoming calls: 

o

 

0 - none

: password is requested before accepting commands 

o

 

1 - no pwd req.

: commands are accepted without requesting the password 

o

 

2 - relay ON

: identifies the caller and activates the relay with free call 

o

 

3 - relay On + pick up

: identifies the caller, activates the relay, then picks up to 

allow further controls through the phone 

o

 

4 - Arm

: arming the module with free call (from version v3.10) 

o

 

5 - Disarm

: disarming the module with free call (from version v3.10) 

o

 

6 - Arm/Disarm

: first free call arms, next free call disarms the module 

(from version v3.10) 

Attention! Arming and disarming the module by phone calls is only possible if 
arming/disarming mode 3, 4 or 5 is set! 

 

SMS forwarding 1-2

: the module forwards the SMS messages received on its SIM 

card to the telephone numbers entered here. This is useful e.g. to forward the 
information received from the GSM provider about the balance of prepay type SIM 
cards. (If these fields are blank, the module ignores incoming SMS messages). 

Important! Never enter here the phone number of the SIM card placed into 
the module, because this would initiate an infinite loop of SMS sent to itself 
right after the first incoming SMS, causing significant expense!

 

 

1-2. Central Phone Nr.

: enter here the phone numbers of the monitoring station(s) 

 

User ID

: the four-digit (0..9,A,B,C,D,E,F characters) user identification number can be 

specified here, which is necessary for reporting to monitoring station. 

 

Monitoring station reporting mode

: report and respectively request confirmation 

to/from only one of the phone numbers of monitoring station, or both phone numbers. 

Содержание GSM Pager3 Z6





















Отзывы:

Похожие инструкции для GSM Pager3 Z6