Telguard TG-7 Series Скачать руководство пользователя страница 5

Страница: 5 / 42

TG-7 Cellular Series Installation & Operating Guide

Table of Contents

Future Testing and Limitations on Use

Terms and Conditions for Use of Telguard Product

INDEMNIFICATION OF TELGUARD

WARRANTY and LIMITATIONS

General Description and Operation

Information Related to Software Settings Fire Systems

Information Related to Software Settings Burglary Systems

Features

Operating Mode

Multiple Alarm Format Support

Complete Supervision of Communication Path

Link Supervision and Standard Line Security

Complete Power Supervision

Telguard Automatic Self-Test Report

Programmable Supervisory Trip Output (STC) Relays

Post-Installation Remote Programming

Diagnostic and Status LEDs

Optional DC Operation (12VDC or 24VDC)

Complete Factory Reset Option

UL and ULC Compliance

Getting Ready

Dealer Account Establishment

Pre-Installation Checklist

PCB Layout

Installation

Summary

Step 1: Register the Communicator

Select the Mode of Operation

UL/ULC Commercial Fire Sole Path (Cellular Only Mode) Features

Decide on a STC Trip Output Strategy

Optional Trip Input

Step 2: Physically Install the Communicator in Desired Location

Identify Location for Placing the Communicator and Mount

Install Optional TG-PEM Accessory into Enclosure (if using)

Complete All Power-Related Wiring Connections

Содержание TG-7 Series











































Результаты поиска

Содержание TG-7 Series

Отзывы:

Похожие инструкции для TG-7 Series

Бренды по названию

Популярные бренды

Telguard TG-7 Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание TG-7 Series

Отзывы:

Похожие инструкции для TG-7 Series

Бренды по названию

Популярные бренды