Telguard TG-7 Series Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 42

background image

TG-7 Cellular Series Installation & Operating Guide

13

56053501 Rev A © 2022 Telguard

Getting Ready

The communicator can only be activated when all necessary accounting information has been added
to the TCC customer database (i.e., the unit has been registered). The database includes information
about the customer account, unit location, and system test plan information.

Dealer Account Establishment

A Dealer Account must be established prior to registration of any Telguard unit. This can be
accomplished by visiting

and completing

Signup This is a one-time event and an acknowledgment from Telguard Customer Service will
include a Dealer Account Number that will be used for all Telguard Digital registrations. Telguard
units can be registered and activated once the Dealer Account has been established.

Pre-Installation Checklist

Before attempting to connect the communicator to the alarm panel, please make sure you have all the
proper parts prior to going to the job site. The following items are shipped with each TG-7 Cellular
Series product:

•

Telguard Cellular Communicator

•

Cellular Antenna

•

Antenna Extension Cable and Mounting Bracket

•

AC Power Adapter

•

Battery Connection Cable

•

Telco Connection Cable

•

Pluggable Screw Terminal Blocks (2-, 2-, 3-, & 6- position)

•

Enclosure Key

•

Quick Install Guide

•

Frequency Warning Label to be applied for installations in Canada (AT&T models only)

•

Tamper Switch Easy-Attach Assembly (TG-7 and TG-7A only or when purchased as an accessory)

Note: When upgrading an existing communicator using the TG-7UB, continued use of some existing
items is necessary. See the instructions provided with the TG-7UB for further details.

PRINTED CIRCUIT BOARD (PCB)

INSIDE METAL ENCLOSURE

TERMINAL

BLOCKS

LTE

ANTENNA

MOUNTING

BRACKET

ENCLOSURE

KEY

AC ADAPTER

12FT ANTENNA

CABLE

TELCO CABLE

BATTERY

CONNECTOR

«
...
17
18
19
20
21
...
»

Содержание TG-7 Series











































Отзывы:

Нет отзывов

Похожие инструкции для TG-7 Series

Бренд: Federal Signal Corporation Страницы: 20

Бренд: ZEN Страницы: 27

Бренд: Dolby Laboratories Страницы: 31

Бренд: i-mobile Страницы: 50

Бренд: Sony Ericsson Страницы: 8

Бренд: GAI-Tronics Страницы: 21

Бренд: UTStarcom Страницы: 72

Бренд: lepow Страницы: 2

Бренд: NAPCO Страницы: 24

Бренд: Nortel Страницы: 160

Бренд: Grandstream Networks Страницы: 11

Бренд: PolySony Страницы: 4

Бренд: Allworx Страницы: 6

ON-AIR 2000 EXECUTIVE

Бренд: BT Страницы: 25

Бренд: Salora Страницы: 33

OPENTOUCH ALE-300

Бренд: Alcatel-Lucent Страницы: 101

Бренд: Aquos Страницы: 186

SCH U520 - Cell Phone - ALLTEL Wireless

Бренд: Samsung Страницы: 196

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды